Jump to content

E7270: Help installing El Capitan


aufannada

Recommended Posts

  • Replies 24
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Yes, I already used EFI El Capitan that you sent both on the FD Installer and on the SSD that has El Capitan installed. And both of them can't boot normally to the desktop. Even if I use boot arg -igfxvesa and / or -no_compat_check. The result is like the picture I sent earlier.

 

20190612_004353.jpg

 

Why do I use the current EFI, because it can install and enter the SSD installed El Capitan. But the problem are :

1. I have to use boot arg -igfxvesa to boot until it enters the desktop.

2. The display is still 4MB after enter the desktop.

 

Maybe this can help a little :

When I execute ssdtPRGen.sh from terminal to generated SSDT.aml

 

ssdtPRGen.sh v0.9  Copyright (c) 2011-2012 by † RevoGirl

             v6.6  Copyright (c) 2013 by † Jeroen

             v21.5 Copyright (c) 2013-2019 by Pike R. Alpha

-----------------------------------------------------------

Bugs > https://github.com/Piker-Alpha/ssdtPRGen.sh/issues <

/Users/aufannada/Downloads/MASTERS/MAC/SYSTEMS/INSTALLER DELL LATITUDE E7270/TOOLS/ssdtPRGen.sh: line 3877: /Users/aufannada/Library/ssdtPRGen/Data/Versions.cfg: No such file or directory

 

System information: Mac OS X 10.11.6 (15G31)

Brandstring: "Intel(R) Core(TM) i7-6600U CPU @ 2.60GHz"

 

Notice: Downloading extractACPITables.zip ...

Notice: Downloading User Defined.cfg ...

Notice: Downloading Sandy Bridge.cfg ...

Notice: Downloading Ivy Bridge.cfg ...

Notice: Downloading Haswell.cfg ...

Notice: Downloading Broadwell.cfg ...

Notice: Downloading Skylake.cfg ...

Version: models.cfg v171 / Skylake.cfg v195

 

 

Scope (_PR_) {222 bytes} with ACPI Processor declarations found in DSDT (ACPI 1.0 compliant)

Notice: Downloading Restrictions.cfg ...

 

Notice: The LFM frequency in Mac-E43C1C25D4880AD6.plist is set to 1300 MHz!

    This restriction can be lifted with help of freqVectorsEdit.sh from:

   https://github.com/Piker-Alpha/freqVectorsEdit.sh

 

Generating ssdt.dsl for a 'MacBookPro12,1' with board-id [Mac-E43C1C25D4880AD6]

Skylake Core i7-6600U processor [0x406E3] setup [0x0705]

With a maximum TDP of 15 Watt, as specified by Intel

Number logical CPU's: 4 (Core Frequency: 2600 MHz)

Number of Turbo States: 8 (2700-3400 MHz)

Number of P-States: 30 (500-3400 MHz)

Adjusting C-States for detected (mobile) processor

Injected C-States for CPU0 (C1,C3,C6,C7)

Injected C-States for CPU1 (C1,C2,C3,C6,C7)

Warning: 'cpu-type' may be set improperly (0x0705 instead of 0x0905)

     - Clover users should read https://clover-wiki.zetam.org/Configuration/CPU#cpu_type

Error: board-id [Mac-E43C1C25D4880AD6] not supported by Skylake – check SMBIOS data / use the -target option

 

Screen Shot 2019-06-12 at 4.19.04 AM.png

It says that :

1. 'cpu-type' may be set improperly (0x0705 instead of 0x0905)

2. Error: board-id [Mac-E43C1C25D4880AD6] not supported by Skylake

 

In Clover Configurator - SMBIOS, Mac-E43C1C25D4880AD6 is MacBookPro12,1 - MacBook Pro (13-inch, Retina, Early 2015) Intel Core i5-5257U @ 2.70 GHz.

 

5257 is not Skylake

Link to comment
Share on other sites

Oh God, I'm very grateful to you Jake. Now it works and booting is very fast entering the desktop. Just a few seconds. The display is now full to 1536MB. I am very happy. Thank you very much, Jake. You are the best.

 

Screen Shot 2019-06-12 at 6.37.10 AM.png

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.

×
×
  • Create New...