Jump to content

EAPD/Jack sense Fix (No sound and jack sense issue after sleep)


EMlyDinEsH

Recommended Posts

Try the attached kext and let me know.

 

here is log

2014. 3. 9. 오전 1:30:41.778 com.apple.kextd[12]: kext org.emlydinesh.driver.EAPDFix  105009000 is in exception list, allowing to load
2014. 3. 9. 오전 1:30:43.000 kernel[0]: EAPDFix v1.5 Copyright © EMlyDinEsH (OSXLatitude) 2013-2014.
2014. 3. 9. 오전 1:31:02.295 com.apple.kextcache[676]: kext org.emlydinesh.driver.EAPDFix  105009000 is in exception list, allowing to load
2014. 3. 9. 오전 1:31:08.000 kernel[0]: EAPDFix: Codec address 0.
2014. 3. 9. 오전 1:31:08.000 kernel[0]: EAPDFix: Failed to get AppleHDA Power state.
2014. 3. 9. 오전 1:32:39.542 com.apple.kextcache[782]: kext org.emlydinesh.driver.EAPDFix  105009000 is in exception list, allowing to load
2014. 3. 9. 오전 1:33:30.000 kernel[0]: EAPDFix v1.5 Copyright © EMlyDinEsH (OSXLatitude) 2013-2014.
2014. 3. 9. 오전 1:33:32.000 kernel[0]: EAPDFix: EAPD is disabled, Enabling EAPD...
2014. 3. 9. 오전 1:33:32.000 kernel[0]: EAPDFix: Codec verb sent successfully to enable Speakers EAPD.
 
 
my alc 270 is not working.
Link to comment
Share on other sites

EAPDFix: EAPD is disabled, Enabling EAPD...

EAPDFix: Codec verb sent successfully to enable Speakers EAPD.

EAPDFix: EAPD is disabled, Enabling EAPD...

 

EAPDFix: Codec verb sent successfully to enable Speakers EAPD.

 

my vt1802p, using appleHDA,2.6.0, in 10.9.2, still no sound after sleep..

in console, it keeps appearing the above two lines.

Link to comment
Share on other sites

EAPDFix: EAPD is disabled, Enabling EAPD...

EAPDFix: Codec verb sent successfully to enable Speakers EAPD.

EAPDFix: EAPD is disabled, Enabling EAPD...

 

EAPDFix: Codec verb sent successfully to enable Speakers EAPD.

 

my vt1802p, using appleHDA,2.6.0, in 10.9.2, still no sound after sleep..

in console, it keeps appearing the above two lines.

 

 

Set the correct node ID in the Info.plist. Read the first post to figure out which node.

Link to comment
Share on other sites

Set the correct node ID in the Info.plist. Read the first post to figure out which node.

I did had set my node ID before I use it. 

Node 0x24 [Pin Complex] wcaps 0x40050d: Stereo Amp-Out
  Control: name="Speaker Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Control: name="Speaker Phantom Jack", index=0, device=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00010050: OUT EAPD Balanced
  EAPD 0x3: BALANCED EAPD
  Pin Default 0x90170110: [Fixed] Speaker at Int N/A

mine is in node 24 isn't it?

 

Link to comment
Share on other sites

hi, thanks for everything u have done, thanks a lot!

I am using a via vt1802p card, and i'm using appleHDA.kext 2.6.0 in 10.9.2. no sound after wake from sleep (but have sound from the headphone after wake). I have been look around for many times but nothing can help.

I even don't know where to start to working on this problem.

codec_dump.txt

if you can take a look at my codec_dump file, that's very kind of you.

sorry for my bad English

 

Link to comment
Share on other sites

I did had set my node ID before I use it. 

Node 0x24 [Pin Complex] wcaps 0x40050d: Stereo Amp-Out
  Control: name="Speaker Playback Switch", index=0, device=0
    ControlAmp: chs=3, dir=Out, idx=0, ofs=0
  Control: name="Speaker Phantom Jack", index=0, device=0
  Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
  Amp-Out vals:  [0x00 0x00]
  Pincap 0x00010050: OUT EAPD Balanced
  EAPD 0x3: BALANCED EAPD
  Pin Default 0x90170110: [Fixed] Speaker at Int N/A

mine is in node 24 isn't it?

 

Nope ... 0x24 is hex, you have to convert to decimal (Base16 to Base10). As you can see here, http://www.openstrike.co.uk/cgi-bin/decimalhex.cgi?input=24&direction=To+Decimal , your actual node is 36. Try using node 36 and let us know. Also, the oinly reason why you have sound via headphones is because your device doesn't have an EAPD for it.

Link to comment
Share on other sites

Nope ... 0x24 is hex, you have to convert to decimal (Base16 to Base10). As you can see here, http://www.openstrike.co.uk/cgi-bin/decimalhex.cgi?input=24&direction=To+Decimal , your actual node is 36. Try using node 36 and let us know. Also, the oinly reason why you have sound via headphones is because your device doesn't have an EAPD for it.

come on, of course I am using 36 in decimal.

by the way, have you seen my codec_dump file at #66, there DID has an EAPD for the headphone (and it is in node 25, which in decimal is 37).

thanks for help.

 

 

 

 

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...