Jump to content

[Solved] D820 Ethernet working but no IP Address


WindowsUser546

Recommended Posts

I installed the appropriate ethernet kext for my Dell Latitude D820 but when I go to the Network Setting in System Preferences, it says No IP Address and if I put one in... it still won't connect to the internet. I think I might have to configure everything by myself..because in Network Diagnostics, everything is failing. Oh well. 

 

Any help would be appreciated.

 

EDIT: Solved using the D620_GMA950_LowRes Pack Ethernet Kext, found down below.

Link to comment
Share on other sites

lspci -nn gave me these results:

00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 01)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 01)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 01)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 [8086:27d4] (rev 01)
00:1c.3 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 [8086:27d6] (rev 01)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 01)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 01)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 01)
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 01)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 01)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e1)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 01)
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 01)
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 01)
01:00.0 VGA compatible controller [0300]: nVidia Corporation G72M [GeForce Go 7400] [10de:01d8] (rev a1)
03:01.0 CardBus bridge [0607]: O2 Micro, Inc. Cardbus bridge [1217:7135] (rev 21)
03:01.4 FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Firewire (IEEE 1394) [1217:00f7] (rev 02)
09:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5752 Gigabit Ethernet PCI Express [14e4:1600] (rev 02)
0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection [8086:4222] (rev 02)
Link to comment
Share on other sites

Which kext did you use? I'd expect you to use AppleBCM5751Ethernet kext as available in the D4x0 or D620 packs.

 

The LAN card should be the same as in the D430/D620 but please post the output of Terminal command lspci -nn or a saved SysProfiler output to verify.

Thanks, I used the D620_GMA950_LowRes_10.6.8 Pack for the Ethernet Kext and it works perfectly! I am running 10.6.3 currently but I'm sure that it will run on 10.6.7. Thanks again. I'll change the title to solved.

Link to comment
Share on other sites

  • Administrators

Ok, so you have the D820 with nVidia Quadro NVS 120M. It'll run 10.6.8 (or 10.7.5) too.

 

You need to remove and replace your Intel 3945ABG wireless card by a supported (mini-PCIe) one if you want wifi on your Hackintosh.

https://osxlatitude.com/index.php?/topic/2120-inventory-of-unsupported-and-supported-wireless-cards/

Link to comment
Share on other sites

Please sign in to comment

You will be able to leave a comment after signing in



Sign In Now
×
×
  • Create New...