Jump to content

Asus G75VW


Zackptg5

Recommended Posts

Specifications:

Processor               : Intel® Core i7-3630QM Processor (6M Cache, up to 3.40 GHz)
Graphics Processor(GPU) : NVIDIA®  GeForce® GTX 670M
Chipset                 : Intel® HM77 Express Chipset
Hard disk               : Sandisk Extreme II 240gb SSD
RAM                     : 12GB DDR3 1600 MHz SDRAM
Wifi                    : Atheros AR9485 Wireless Network Adapter
Bluetooth               : Atheros AR3012 Bluetooth V4.0+HS
LAN                     : Atheros AR8151 PCI-E Gigabit Ethernet Controller
Audio                   : VIA® VT1802  High Definition Audio
USB 3.0                 : Intel Panther Point PCH - USB 3.0 xHCI Controller
Touchpad                : Synaptics Touchpad
Webcam                  : USB2.0 UVC HD WebCam
Card reader             : Generic Card Reader
Monitor                 : 17.3 LED 1920x1080
Optical Drive           : DVD±RW (±R DL) / DVD-RAM
Battery                 : 8Cells 5200 mAh 74 Whrs
Interface :
1 x Microphone-in jack
1 x Headphone-out jack
1 x VGA port/Mini D-sub 15-pin for external monitor
4 x USB 3.0 port(s) 
1 x RJ45 LAN Jack for LAN insert 
1 x HDMI
1 x SPIDIF speaker out
1 x mini Display PortI

Working:
Graphics with Acceleration
Audio using VoodooHDA
Bluetooth
HDMI

mini Display Port
LAN
USB3.0
Webcam
Optical Drive
Battery
Card reader
Synaptics Touchpad
Sleep, Processor P&C-States with Native power management
Fn Hotkeys

VGA - see VGA section below

Not working:

Atheros AR9485 Wireless Network Adapter (need to replace with supported card, I replaced with BCM4352)

Issues:
**In mavericks only, when using a mac mini or mbp smbios, flash and quicktime videos will freeze. When using an ivy bridge iMac smbios (13,2/1), the will be random freezes for no reason whatsoever (see fix at bottom)

For Installation:
EDP STEPS:
Follow the Steps in the link below, starting with Pre installation, Installation and Post Installation:
http://www.osxlatitude.com/edp/documentation/

(OR)

MANUAL STEPS:
Steps to get it working

Format hard drive as MBR


Due to the prompt for using a custom extra folder not showing up at all for me during the pen drive my hack installation, I did the following:

1) Right click on MyHack.app -> show package contents
2) Navigate to: Contents -> Resources -> Extra
3) Open the boot.plist and change the following:
i) Graphics Mode - 1920x1080x32
ii) Delete timeout and replace it with Instant Menu - Yes (Optional)

iii) Kernel Flags - kext-dev-mode=1 (yosemite only) nv_disable=1 (yosmite and mavericks)

iv) GraphicsEnabler - no (for mav and yose) yes (for ml)

v) IGPEnabler - no
4) Open Extensions folder
5) Delete the AppleRTC kext
6) Copy GenericUSBXHCI.kext to it

Then do the normal MyHack Install method (say yes at mbr patch prompt and if the prompt for an extra foder does show up, pick the generic one)

Mavericks and Yosemite only: After MyHack is installed to the pen drive, add the kernel flag: nv_disable=1 to the boot.plist or you will get a black screen

Repair permissions and stuff and install normally picking 'generic extra folder' in the install.

Post Installation:

Bootloader: Latest chameleon

Options:
DropDSDT=Yes
EthernetBuiltIn=Yes
GraphicsEnabler=No
IGPEnabler=No
GraphicsMode="1920x1080x32"
Kernel=mac_kernel (not for yosemite)

Kernel Flags=kext-dev-mode=1 (yosemite only)
Legacy Logo=Yes
InstantMenu=Yes
UseKernelCache=Yes

SmBios: MacBookPro 10,1 for mountain lion and yosemite
iMac 13,2 for mavericks

Kexts/Patches (All kexts installed to S/L/E)

Copy NVDAResman.kext from the root of the pen drive to S/L/E of the new installation (mav only)

libclh.dylib patch and OpenCL patch (mountain lion only)
latest fakesmc, plugins, and hardware monitor
In fakesmc info.plist -> change "smc-name" to "smc-huronriver"
and change the values in keys: "REV", "RVBF", and "RVUF" to:
"<02030f00 0036>" for mbp 10,1 smbios (ML and Yose)
"<01530f00 0013>" for imac 13,2 smbios (Mav)
VoodooPS2Controller.kext for mouse and trackpad
Trim Enabler patch (only for ssds) - OS X version specific
GenericUSBXHCI (yosemite has a different one than prior OS X versions)
AtherosL1CEthernet (ALXEthernet works too but has memory leak when system sleeps)
AppleRTC patch

Asusg75's patched AnyiSightCam (AnyiSightCam.kext.zip) - mav only
AICPUPM patch (AICPUPM Patch for UEFI V2.app.zip)
Pike's SSDT generation script 
Asus Fn Hotkey driver
Needs custom efi string for graphics card for screen backlight to work and to eliminate need for graphics enabler in boot loader (670m.hex.zip)

*In yosemite, graphics enabler doesn't work and so without this, you will have a black screen unless you disable QE/CI
Rehabman's ACPIBatteryManager.kext
AirPortBrcm4360.kext id insert for wifi card (14e4,43b1)
Bluetooth Firmware Uploader
Custom VoodooHDA 2.8.6 (VoodooHDA.kext.zip), see Sound below
AGPM patch - see power management below
**Optional** Nvidia Cuda Driver

Delete E/E folder

Sound

Delete AppleHDA.kext
Install voodoohda

*After patched voodoohda is installed:
1) Go to Audio Midi Setup in Utilities and create a new multi-output device
2) Check both speakers
3) Uncheck drift correction if it is automatically checked for you
4) Make sure both speakers under the multi-output device have the same sample rate (I'm using 48000hz)

Note: Whenever headphones are plugged in, you will need to manually select it as the output device

 

DSDT Patches

DTGP
wifi_bt 4 toggle, brightness keys, and keyboard backlight patches for fn hotkey driver
custom battery patch (DSDT Patches.zip)

GPU/CPU Power Management
 

Mountain Lion/Yosemite:
1. Just go to AGPM.kext in S/L/E and copy it to your desktop
2. Then open it and got to: show package contents -> contents -> info.plist
3. Then navigate to: IOKitPersonalities->AGPM->Machines
4. Expand Mac-C3EC7CD22292981F (mbp 10,1) or 
5. Add a new dictionary called: Vendor10deDevice1213
6. In this new dictionary, add a new number titled: control-id
7. Give it a value of 17
8. Add a new dictionary called: Heuristic
9. In this new dictionary, add a  new number titled: ID
10. Give it a value of 0
11. Navigate back to GFX0 under the smbios
12. expand heuristic under it and change the value of ID to 0 (0 is for fermi cards and 4 is for kepler)
13. To create ssdt:
   i. After downloading ssdtPRGen, open terminal and type: ~/ssdtPRGen.sh -w 3
   * This will generate an ssdt with the ivy bridge work arounds. Without the work arounds, you're cpus will be stuck at "x8.0" all of the time.
 
Mavericks Only:
1. Change smbios from iMac 13,2 to iMac 12,1
2. AGPM patching same as above except apply these fixes to iMac 12,1 smbios instead
3. Under gfx0, delete "BoostPState", "BoostTime", and everything under the "Heuristic" dictionary except the "ID" number
4. Go back into S/L/E and copy AppleGraphicsControl to your desktop
5. Open it and go to Contents -> Plugins -> AppleGraphicsDevicePolicy -> Contents 
6. Open the info.plist and navigate to: IOKitPersonalities -> AppleGraphicsDevicePolicy -> ConfigMap
7. Create a new string and name it: Mac-942B5BF58194151B
8. Make its value: none
* This will prevent booting to a black screen
9. A special ssdt must be generated to get proper cpu power management:
   i. After downloading ssdtPRGen, open terminal and type: ./ssdtPRGen.sh -c 0
   * This will generate an ssdt for sandy bridge smbioses (like the iMac 12,1) to get proper cpu power management
 
Explanation for using iMac 12,1 Smbios in Mavericks
For unknown reasons, using the iMac 12,1 smbios (with proper smbios and graphics kext patches outlined above) is the only one we've found to work well. Macbook pro and mac mini smbioses both lead to complete system lockups when running flash or quicktime videos and the iMac 13,2/1 smbioses work most of the time, but will lead to random and unpredictable system freezes. 
According to Intel, ivy bridge is backwardly compatible with sandy bridge which is why this works well. Ivy bridge is only a smaller, slightly more power efficient/slightly more powerful version of sandy bridge. There's not much of a difference between them. 
 
Credits to asusG75 for discovering this coveted freeze fix
 
VGA
After the system is booted, plugging a monitor in via VGA doesn't work.
However, if you plug the monitor in via VGA and THEN boot, it shows up and works fine. Then you can unplug and plug it in later after that boot is finished. 

 

Bios Limitation?

I've been unable to boot to any gpt partitions besides windows on internal hdds. I've read that it is a bios limitation but others have reported it working with osx. Still under investigation.

 

About this Mac Picture:
Attached below is a more appropriate picture to replace the default iMac picture when using an iMac 27 inch smbios. Place file in:
System/Library/CoreServices/CoreTypes.bundle/Contents/Resources
Make a backup of the original file if the picture doesn't suit your tastes. If using another smbios, just copy the name of the file you wish to change and place in the folder mentioned.
post-12954-0-60851900-1408329140_thumb.png
 
Also attached are 3 different picture that can be used to replace the apple logo in About this Mac. Just changed the name of the picture of your choice to "MacOSX.tiff" and copy it to: 
System/Library/CoreServices/loginwindows.app/Contents/Resources
Of course back up the original if you don't like them. 
post-12954-0-69147000-1408329152_thumb.pngpost-12954-0-54983800-1408329155_thumb.pngpost-12954-0-22284900-1408329159_thumb.png

ssdtPRGen.app.zip

AboutThisMacMod.zip

Link to comment
Share on other sites

Updated guide with my hack install method

 

One problem though: After install, it hangs at pci config end. I've tried the npci flags but they didn't work. This is a problem with some extra thing the myhack installer does because this doesn't happen with the uni_beast method. I also declined to remove any of the "problematic kexts" as they don't cause any problems for me. Any suggestions to what the issue is?

Link to comment
Share on other sites

After a bit of a hiatus from this, I've finally had the time to get back to getting everything working. I've updated my first post with lots of updates including fully working sound (subwoofer and everything) thanks to some help from slice at insanelymac forums.

I've gotten back to comparing myhack to unifail and I somehow overlooked the most obvious thing ever. In the e/e folder on the unifail pen drive was GenericUSBXHCI.kext. I need that because I have all usb 3.0 ports. I put that kext into the e/e of the my hack pen drive and it now works without a hitch.

Link to comment
Share on other sites

After solving a black screen issue (GraphicsEnabler doesn't appear to work properly in yosemite), I got yosemite installed. Updated the guide.

 

For this laptop: mountain lion and yosemite work great, mavericks sucks. I'm sure many other users will draw the same conclusions for their computers

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...