Jump to content

Leaderboard


Popular Content

Showing content with the highest reputation since 10/02/17 in all areas

  1. 9 points
    Dell Latitude/Inspiron/Precision/Vostro/XPS - Clover Guide Up to Sierra Only High Sierra Guide below Mojave Guide Warning: Follow guide at your own risk, I hold no responsibility if you brick your system or destroy all data during the process. If you're creating the installer from a real Mac, make sure you don't accidentally select the real Mac drive when installing Clover loader. It may cause your Mac to not boot again. You've been warned! BIOS: Set to Default, apply, then set SATA Operations to AHCI, set Boot List Option to UEFI Requirements: 1. A downloaded OS X El Capitan / Sierra Application from the Mac App Store 2. USB flash drive (16GB minimum) 3. Clover Configurator (Included in Hack_Tools attached below - might not be the latest) 4. Clover Loader 5. ShowHiddenFiles.app (Included in Hack_Tools attached below) 6. A system running OS X to create the USB Installer 7. A supported Wireless card, Intel wireless are NOT supported Overview 1. Prepare a Bootable USB Drive (8GB minimum) 2. Install OS X El Capitan / Sierra 3. Post Installation 1: Prepare Bootable USB Drive This step extracts the OS X Installer contents, then installs Clover bootloader to the USB stick. 1. Insert the USB drive on a running OS X system 2. Open /Applications/Utilities/Disk Utility 3. Highlight the USB drive in left column 4. Click on the Partition tab 5. Click Current and choose 1 Partition 6. Click Options... 7. Choose GUID Partition Table 8. Under Name: type USB (You can rename it later) 9. Under Format: choose Mac OS Extended (Journaled) 10. Click Apply then Partition 11. Go to Applications, right click on Install OS X El Capitan / Sierra =>Show Package Contents=>Contents=> SharedSupport 12. Mount InstallESD.dmg 13. Launch ShowHiddenFiles and select Show Special Files ( app attached at the end of guide) 14. Mount BaseSystem.dmg (hidden) from OS X Install ESD 15. Use Disk Utility to restore OS X Base System to USB (see image below) 16. After restore is complete, USB is now renamed to OS X Base System. Go ahead and rename it to Install OS X El Capitan 17. Go to Install OS X El Capitan/ Sierra=>System=>Installation and delete the alias Packages 18. Copy Packages from root of OS X Install ESD to Install OS X El Capitan/Sierra=>System=>Installation 19. Copy BaseSystem.dmg and BaseSystem.chunklist (hidden files) from OS X Install ESD to root of Install OS X El Capitan/Sierra 20. Launch ShowHiddenFiles and select Hide Special Files 21. Download Clover 22. Launch Clover package installer 23. Hit Continue, Continue, Change Install Location... 25. Choose Install OS X El Capitan/Sierra 26. Hit Continue, then hit Customize. Select these items: Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\DataHubDxe-64 Drivers64UEFI\FSInject-64 Drivers64UEFI\SMCHelper-64 Drivers64UEFI\ApfsDriverLoader-64 Drivers64UEFI\AptioMemoryFix-64 Drivers64UEFI\PartitionDxe-64 Add to Drivers64UEFI\HFSPlus.efi (Not included in Clover installer) Note: For non UEFI BIOS, see Note1 of post #2 27. Click Install 28. After installation of Clover, the hidden EFI Partition will appear on the Desktop 29. Download the Generic EFI + Bootpack for your model in post #2, replace the contents to the root of the EFI partition, replacing the existing folders ( Boot and Clover folders - not merge) Note: Make sure to check the Update section in Post #4 for updated file if any 30. You are now ready to install OS X El Capitan/Sierra Note: Make a directory in the USB Installer and copy Hack_Tools, Clover package and EFI folder to it for easy access in Step 3 2: Install OS X El Capitan/Sierra 1. Turn on the computer with the USB Installer connected 2. Press F2 to configure the BIOS Sata Operaton -> AHCI Secure Boot -> Disabled Boot List Option -> UEFI. Enable Legacy Option ROMs (Disabled for Skylake and above) Apply and Exit 3. Hit F12 during boot, choose under UEFI Boot: 4. When Clover boot screen appears, choose Install OS X El Capitan/Sierra 5. The system will then boot into the OS X Installer 6. Choose your language and hit -> to continue 7. For a new installation of OS X, you MUST erase and format the destination drive according to the following steps before continuing. *If you are upgrading from Lion, Mountain Lion, Mavericks, or Yosemite and you want to keep your files and apps, skip steps a-i. a. From the menu bar, click Utilities -> Choose Disk Utility b. Highlight your target hard drive for the El Capitan installation in left column. c. Click Erase tab d. Under Scheme: GUID Partition Map e. Under Name: type Macintosh SSD (You can rename it later) f. Under Format: choose Mac OS Extended (Journaled) g. Click Erase h. Click on Partition Tab to add more partition if you prefer i. Close Disk Utility 8. Click Continue, Continue, Agree 9. Select Macintosh SSD, or name of your existing drive, where you want to install El Capitan and click Continue 10. Upon completion, system will restart 11. Press the F12 to choose boot device 12. Choose under UEFI Boot: 13. When Clover boot screen appears, choose Macintosh SSD or name of your existing drive The system will boot into the new drive, and complete the installation: 14. Launch the terminal and enter the following command diskutil list Note: If you see the following, then follow steps in Post #3 Under Core Storage before proceeding /dev/disk1 (internal, virtual): 3: Post-Installation Install Clover loader to Macintosh SSD 1. Launch Clover package installer 2. Hit Continue, Continue, Change Install Location... 3. Choose Macintosh SSD 4. Hit Continue, then hit Customize. Select these items: Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\DataHubDxe-64 Drivers64UEFI\FSInject-64 Drivers64UEFI\SMCHelper-64 Drivers64UEFI\ApfsDriverLoader-64 Drivers64UEFI\AptioMemoryFix-64 Drivers64UEFI\PartitionDxe-64 Install Clover Preference Pane Add to Drivers64UEFI\HFSPlus.efi (Not included in Clover installer) Note: For non UEFI BIOS, see Note1 of post #2 5. Launch ESP Mounter Pro, select the disk you have OS X installed on (ie. disk0s1) - app in Hack_Tools 6. Copy the EFI folder from the USB installer to EFI partition of Macintosh SSD (replace not merge) 7. Copy kexts from /EFI/Clover/Kexts/Other/CopytoLE to /Library/Extensions of Macintosh SSD Note: Ignore warning/error messages and click OK, then run commands below. 8. Repair permission and rebuild cache. Run command from terminal (or run permission.sh found in Hack_Tools) sudo chmod -Rf 755 /L*/E* sudo chown -Rf 0:0 /L*/E* sudo touch -f /L*/E* sudo chmod -Rf 755 /S*/L*/E* sudo chown -Rf 0:0 /S*/L*/E* sudo touch -f /S*/L*/E* sudo kextcache -Boot -U / 9. Go to System Preferences Enable Clicking for Trackpad Allow apps downloaded from: Anywhere for Security & Privacy (optional) Note: For Sierra and up, run this in terminal instead: sudo spctl --master-disable 10. Generate own SMBios and SSDT.aml (For Haswell and up, you can enable PluginType in Config instead) Launch /EFI/Clover/Config.plist with Clover Configurator (Included in Hack_Tools attached below) On the left, click on SMBIOS Click on the Up/Down arrow on the right Select the model most suited for your system or use same model included in bootpack, generate a new serial Close Clover Config and save the file. Execute ssdtPRGen.sh from terminal (Included in Hack_Tools attached below) Place generated SSDT.aml in /EFI/Clover/ACPI/Patched Please use beta version of ssdPRGen.sh to generate SSDT.aml for newer system 11. Make sure to disable hibernation as it's a prerequisite to get sleep & wake to work properly on a Hackintosh: sudo pmset hibernatemode 0 sudo rm -f /var/vm/sleepimage sudo pmset hibernatefile /dev/null 12. Congratulations! You are done! Hack_Tools.zip When posting for HELP, please include full system specs and attach debug files. If you're not able to start the installer, then attach the Clover folder and include screenshot(s) of the error / KP by booting with verbose + debug 0x100 mode Credits: All apps, kexts and DSDT patches used in creating this guide go to the developers that created them. I take no credit other than putting this guide and bootpacks together.
  2. 6 points
    Last update: 11 Apr 2019 I've finally been able to play with that card on a laptop, fitted with an M.2 2230 Key A+E WLAN slot, that I targeted for Mojave. /!\ The 1st thing I want to report is that I encountered difficulties booting my Mojave USB installer and installing macOS with the card plugged in and without any particular tuning for it. I had to disable wireless in BIOS to be able to install Mojave. Once it was installed, booting Mojave with wireless enabled in BIOS would cause quite severe lag and performance degradation once at the desktop, as if the card just clogged up CPU ressources. /!\ Searching through the Web for that DW1820A/BCM4350, I came accross a few forum posts/threads that mentionned: rolling back the Yosemite IO80211Family kext to get the card to work, although with instability and regular KPs removing AirPortBrcmNIC plugin kext from IO80211Family kext, patching AirPortBrcm4360 plugin kext with the id of the DW1820A and installing AirportBrcmFixup kext with a couple of parameters (Credits to Hugotai, cf. his post @Voldemort's place, 2nd Dec 2018) Whilst I did not really contemplate doing the 1st thing, I did envisage the 2nd one and started to look at the differences between Yosemite's version of IO80211Family kext and Mojave's. The main difference I had already noticed was that device id 14e4:43a3 was handled by AirPortBrcm4360 up to Sierra 10.12 and by AirPortBrcmNIC since High Sierra 10.13. Building on Hugotai's success, I seeked to work out an easier solution that would not require kext removal and Info.plist patching but, instead, something that could be implemented through hardware properties injection, either through DSDT patching or Clover configuration. Once Hugotai's solution was verified and confirmed, I worked out the following Clover-based solution for HighSierra/Mojave: identify the IOReg/ACPI device to which the DW1820A card is attached (use IORegistryExplorer app to that effect) inject the following properties either in DSDT or through Clover (latter recommended): compatibility of the card with Broadcom chips 14e4:4331 or 14e4:4353 that are handled by IO80211Family's PlugIn kext AirPortBrcm4360 optionally, add SysProfiler's cosmetic info such as PCIe Slot, card's make and model, etc. if your raw/BIOS DSDT has no individual entry under the PCI root bridge for the device, select "FixAirport" ACPI Fix in Clover. That'll create a device "ARPT" @0 under the root bridge and that's what you'll inject properties to. and that's it ! Nothing to do to IO80211Family kext ir its PlugIns which all remain untouched/unmodified/full vanilla in /S/L/E. It really could not be simpler... NB: if your card's country code requires to be changed, add the following steps: install AirportBrcmFixup kext in /L/E + repair permissions + rebuild your cache or inject it through Clover's EFI/CLOVER/kexts/Other add boot argument brcmfx-country=XX (where XX is the target value, eg: US, FR, #a, etc.) to the Boot section of your Clover config but, beware, I found that using AirportBrcmFixup has some non-negligable negative impact on wireless performance (much reduced rate). Example: On my laptop, the DW1820A was found attached to device RP03.PXSX located at IO address 0x001C0002, i.e. 1C,2. The DSDT patch required to inject properties could look like this (devices names will differ from one computer to another of course!): Device (RP03) // PCIe Root Bridge { name (_ADR, 0x001C0002) [...] [...] [...] Device (PXSX) // DW1820A card attached to this device (FixAirport fix required if such device is missing) { Name (_ADR, Zero) [...] [...] [...] Method (_DSM, 4, NotSerialized) // _DSM: Device-Specific Method { If (LEqual (Arg2, Zero)) { Return (Buffer (One) { 0x03 }) } Return (Package () { "AAPL,slot-name", // Optional Buffer () { "WLAN" }, "device_type", // Optional Buffer () { "Airport Extreme" }, "name", // Optional Buffer () { "Airport" }, "model", // Optional Buffer () { "Dell DW1820A 802.11ac wireless" }, "compatible", // Mandatory Buffer () { "pci14e4,4331" // Declares compatibility with BCM94331; "pci14e4:4353" for BCM43224 may also be used } }) } } } An easier alternative is to inject those properties in Clover via Clover Configurator app. This can be done within the Devices section by injecting the desired properties in the Properties sub-section: In the left part, add the PCIe address of the targeted device in the form PciRoot(0x0)/Pci(<root device address>)/Pci(<actual device address>) In the right part, add the above properties in single lines and with the right types (String, Data, Number) For instance, in the case of my laptop, the target device will be PciRoot (0x0)/Pci(0x1C,0x02)/Pci(0x0,0x0) for PCI0@0->RP03@1C,2->PXSX@0. Then, properties will be injected as lines of keys of 3 x possible types: strings, hex data blocks or numbers. For instance, to declare compatibility with 14e4:4353, the line will consist of Property Key set to compatible, Key Value set to pci14e4,4353 and Key Type set to STRING. The complete properties injection will be: Device = PciRoot(0x0)/Pci(0x1c,0x02)/Pci(0x0,0x0) Key = compatible | Value = pci14e4,4353 | Type = STRING Key = AAPL,slot-name | Value = WLAN | Type = STRING (optional) Key = device_type | Value = Airport Extreme | Type = STRING (optional) Key = name | Value = Airport | Type = STRING (optional) Key = model | Value = Dell DW1820 (BCM4350) 802.11ac wireless | Type = STRING (optional) Once the device properties are injected in Clover or DSDT, there's nothing left to do but reboot the computer. The DW1820A card will then be fully active and capable to connect to 2.4/5GHz networks at full speed. On the Bluetooth side, once the usual Rehabman's kexts are installed (BrcmFirmwareRepo + BrcmPatchRAM), the BT4.1 module will be fully operational and capable of supporting AirDrop and Handoff! Links: Clover Configurator app Rehabman's Broadcom Firmware patching kexts Acidanthera AirportBrcmFixup kext
  3. 5 points
    Last update: 17 Sep 2017 UPDATE: 17 - 09 - 2017 Just wanted to clear few things about my commitments to community, and development on my projects which has been going slow due to my personal life as I have been hit really hard since an year, and I am trying to sort out personal things still. So decided to take timeout on my commitments to my projects and put my attention on personal life first. Don't expect any regular updates on this project and others projects of mine till end of this year 2017. It does not mean I will not be working, and it is just that I won't post any update or respond to you all unless I have something worth to share. I know many of you are disappointed with me and some of my choices/decisions for the last one year, but believe me I had no other option and good reason for that. So your patience will be rewarded properly once I have started releasing updates as I have big plans and willing to commit myself to long term development, and I apologize for not keeping up with promises so far. In case I fail to keep up like I promised above, then I will give up and release all of my work to others to continue. Hope you understand and support me with beta tests when I need them Thanks Hi everyone, This is a multitouch driver for ELAN, FocalTech and Synaptics touchpad for Mac OS X based on the documentations available and some ideas from VoodooPS2, ApplePS2 and Linux open source code. I have successfully accomplished everything so far and added many new features to take advantage the touchpad completely to make it close to Apple touchpad in every way. Also my driver is implemented with my own universal logic for all the features, so it can be adapted to all touchpads easily and I'm still improving these to achieve even better results. My driver supports every hardware version of ELAN touchpads except version 1 (which is too old and can't find in existing notebooks will support that if i get some testers), mostly all available FocalTech touchpads and Synaptics touchpads (still experimental) with firmware version v7.5+. NOTE: For Synaptics, it was developed based on my touchpad hardware i have, so support is limited to touchpad with firmware version 7.5+ only, but will try to improve support other hardwares also if users interested in my features and help me with beta testing. FOR BUG REPORTING: Please read the below threads which explain the features after installing the driver, so you can understand and learn how to use every feature. If anyone still have doubts/issues then PM me to get help from myself (or) post them in other thread about issues so others can help you. I will respond to you mostly during weekends only for some time. FEATURES DETAILS: (UPDATED FOR v4.6) Touchpad features: Click here to learn Keyboard features: Click here to learn Supports OS X version 10.6 or later (10.6 support is only from v4.4) For Prefpane, try to install the version from this link, and add the prefpane to start up items: http://www.hackintosh.zone/file/997-correct-preference-pane-trackpad-macos-sierra/ UPDATE: 06-06-17 Hi everyone, It has been long time since I have given you all an update on my development. The reason for this was I had a pretty rough personal life and busy time in my job last few months, so I was really under big stress and had busy days which did not allow me to do any progress on my projects. Good news is that I was able to sort some of my issues, and find some time to continue my projects again. I have already done some analysis on my project, and figured that I had to do some major code rewrite (most of the code was depending around work arounds which are not optimized well for the time being back then) in order to better support future hardwares and also improve features with ease. My plan is Setup a way to support and track bugs from users Setup a way to gather feedback from users Re-build the project from the scratch with good design for cross-platform support in mind, to support multiple touchpad vendors and interfaces (thinking about I2C) as universal driver Refactor the project code with as much clean code (so when I make it open others can understand) as possible of mine from the scratch Finish basic features (Keyboard and Mouse emulation) Integrate basic vendor specific features Develop and Integrate basic prefpane of mine Release first beta to test Integrate and implement my old driver features one by one for better stability Update prefpane for new features and release another beta Update and improve support for newer hardware based on linux and other sources Finish integrating all the features of old driver by reviewing each one with community feedback Add new features and improve it's stability and performance I have big list of TODO's, but I promise this time that I will try to finish each of them as soon as possible with a beta release happening very soon before the end of this month in best case. Understand your patience is really needed here, as I do not want to rush and have limited time of mine. Also, I am gonna give weekly update on my progress if possible when I have finished my milestones. I will try to respond to your PM during weekends, and if you want to be beta tester then send me your skype ids with GMT time via PM. One more thing, current version of my driver is deprecated and so will not be continuing this. But, I will try to give you some support if there is a need before I finish my new version of driver for any issues which are not big enough for time being. Thanks for your support and co-operation. PS: Sorry for those who want my project to be open sourced now, as I cannot do that until I finish above TODO's. Hope you understand, and support me as I really worked hard on this project. I have worries to get this open right now, and understand that with more people development can progress faster but opening this right now might create issues and end myself supporting to the development in the long run due to fragmentation. I would request you to go through plist editing for controlling the features (as I have a lot of them and its important users to know about those details, because it will allow the driver to be tweaked as you want and my default values are not going to be best for every touchpad or user) for now (will make my own prefpane very soon within 3 months, and its a promise). Going to update my thread which details the features every week one after another for keeping it updated with latest version. Version v4.7 beta 5 (10 - 12 - 2016) (work in progress, available to try from attachments). Added back feature multi finger drag due to users request (can be dragged using 1-3f, Note: This drag wont be as smooth as 1f because the data is not as good as 1f in 2-3f which is why I stopped working on this long time ago, but currently it works nicely and usable in my touchpad. So its usage varies to each touchpad). You have to hold fingers for 2-3 sec at fixed position and move to trigger drag. Improved support for Sierra Support for new style prefpane (most of the features wont control my feature, but I will fix them by next weekend to match them) [Drag, scroll, double click speed can be controlled inside Accessibility Settings->Mouse & Trackpad] [Experimental] USB mouse can now stop trackpad if you enable Accessibility setting of Ignore Trackpad [Works only in 10.10 or lower (?). Will find a way for new OS X versions asp] Improved scroll inertia with more control options in Plist to choose Fixed Sierra Caps Lock bug using a workaround Fixed a bug with some new ELAN touchpads which have issues with virtual buttons acting weird if pointing was enabled at button area, so added option to diable/enable this in plist Fixed sierra OS X functions like Launchpad, Dashboard, Mission control etc., which are not working by redirecting to new keyboard shortcuts. (Needs to be configured at Keyboard shortcuts) Updated support for Asus keyboard backlight with two levels Several minor bug fixes and improvements And more to come as am still looking at improving others things that are buggy and also using feedback from users Version v4.6.5 Released Major code optimizations Updated support for 10.12 (Still some Fn keys wont work, will try to fix close to release) Added plist options to control Apple Trackpad prefpane values for 10.12 Several bug fixes and improvements Version v4.6 Fixed CapsLock key change plist option Fixed a firmware bug in ELAN v3 hardware Updated driver to accept new revisions of ELAN Touchpad to be recognized as Version 4 Added plist option to disable the touchpad when LID id closed (Enable back auto when its opened)) which will stop strange behavior from touchpad when using HDMI in some systems. Pointer acceleration enhancements (new plist options to control) Partial support for the extra buttons and track point from Synaptics trackpad Improved support for synaptics Updated documentation for features Several minor bug fixes and optimizations Version v4.5 Added new plist option to control touchpad edges dead zone Added plist option to change 2f and 3f tap default actions Added option to tweak pointing acceleration Added 4f pinch gesture and plist option (ELAN and Focaltech) Updated plist options to better organize Improved 2f dragging in clickpads Improved edge swipes Fixed synaptic touchpad sleep issue seen in some systems Fixed some keyboard bugs Several improvements, minor bug fixes and optimizations Version v4.4.5 : Improved support for Synaptics touchpads (Clickpad working fine now) Updated support for new ELAN touchpads Improved edge swipes Fixed a bug with Karabiner app to allow mapping Several bug fixes and optimizations Version v4.4 : Released (For Asus keyboard backlight auto off, use updated DSDT patch and v2.5 Fn keys kext) Improved support for Synaptics touchpad (Clickpad still have some issues so i need beta testers) Improved support for some new ELAN and Focaltech touchpads Improved pointer acceleration Reworked scrolling Improved Swipes, Zoom and Rotations Added more plist options to tweak the gestures and option to control delay after sleep Added GIGABYTE Fn key mode layout Added support for 10.6 (32bit build) Fixed several bugs in both keyboard and Touchpad Optimizations Version v4.3 : Added support for Synaptics touchpads (Firmware v7.5+) found in new laptops but still its experimental for others as it has not been tested on many laptops. (Tested only on Lenovo Z50-70 and G400) Added support for unsupported touchpads to work in enhanced mouse mode without multi touch Improved support for Focaltech and ELAN touchpad (especially ELAN v2) Improved pointing and scroll with new smoothing features and other improvements which can be controlled in plist Improvements and optimizations for all features Added plist option for keyboard to make Num Lock into clear instead of soft controlled num lock mode Added Fn keys mode layout for Lenovo Added support for ACPI brightness controls from EC calls (You have to use DSDT patch) Fixed many bugs For the complete change log of all the updates follow this thread: https://osxlatitude.com/index.php?/topic/1966-elan-touchpad-driver-issues/ FEATURES OF ELAN v4 HARDWARE, FOCALTECH and SYNAPTICS: (Supports up to five fingers touch) Mouse mode with Virtual Buttons Left, Right and Middle Tapping - Up to 5 fingers Clicking - Up to 5 fingers Dragging : Tap to release and Finger Lift ⃠Left Button Drag, Double Tap Drag, Single Tap Drag and Click Drag Corner Tapping Scrolling - Single finger Edge and Two Fingers swipe Continuous, Linear, Sling and Inertial scroll effects Finger Press - Up to 5 fingers Swiping - Edge, Three and Four Fingers Zoom - Two fingers pinch zoom, OSX Zoom with Keyboard 4 (Elan, Focaltech) & 5 fingers Pinch gesture Rotations - Arc and Swipe Rotations Accidental Input/Palm check when typing Fn Keys Mode Features Toggle Full customization FEATURES OF ELAN v2 and v3 HARDWARE: (Supports up to three fingers touch) Mouse mode with Buttons Left, Right and Virtual Middle Tapping - Up to 3 fingers Dragging - Tap to release and Finger Lift ⃠Left Button Drag, Double Tap Drag and Single Tap Drag Corner Tapping Scrolling - Edge Scroll and Two Fingers Continuous, Linear, Sling, Circular and Inertial scroll effects Finger Press - Up to 3 fingers Swiping - Edge and Three Fingers Zoom - Two fingers pinch zoom, OSX Zoom with Keyboard Rotations - Arc, Circular and Swipe Rotations Accidental Input/Palm check when typing Fn Keys Mode Features Toggle Full customization HOW TO INSTALL: Remove any existing "ApplePS2Controller, VoodooPS2Controller, AppleACPIPS2Nub, ApplePS2Keyboard and old Elan Touchpad" kexts if you have already installed from the HDD '/System/Library/Extensions ', '/Extra/Extensions', and '/System/Extensions/Library/myHack.kext/Contents/Plugins/' (if you used myHack USB installer for OSX). If you use USB installer to boot (used to install OSX), then you have to remove the above kexts from USB '/Extra/Extensions'. Install the Kexts (Recommended to use Kext utility for installing) inside the attached zip file using any kext installing methods (In clover, some systems may have problems with kext injection, so try to install them to System/Library/Extensions in that case). 
 ​ NOTE: From v3.3, there is only one kext as my driver in the attached zip file. For Support PM me or POST here . I may respond slowly sometimes due to busy life. NOTE: Please don't mirror my files at other places, let the people know about this thread for the latest version and support. NOTE: I've worked very hard on this driver (especially ELAN v2, 4 and Focaltech without hardware) and will try to continue support in future. I do the development everyday with some time dedicated to this and many other projects. But i need your support so i can get more time to spend on these projects for improvements. Also we maintain this website without ads for all of you and it costs a bit for us to host. IF POSSIBLE PLEASE MAKE A DONATION BY CLICKING BELOW PAYPAL DONATE BUTTON FOR ME Paypal: FOR WEBSITE DONATE HERE: http://www.osxlatitude.com/donate/ THANKS FOR YOUR SUPPORT I would like to thank following people for beta testing the driver and providing valuable feedback: Leon, Ramalxlama, Shin zon, Sherlocks, Dragon, Ðнтошка, Thomas benhamou,68x, Eli and many others. SOURCE: Project source code: https://github.com/E...Touchpad-Driver I am still doing some major work with beta testers to improve the features and stability, so I cannot update my git until its done, because it may allow others to modify and distribute their own version which can miss my changes and also worried about something else too which I do not want to mention here. I want to support this project for very long time and did spend hundreds of hours so far with testers (without hardware) and implemented many of the features myself from the scratch. So, I deserve and have rights to not to update my project source until I feel confident. The base of the Apple PS2 open sources I have used for my project are pretty much same which you find in the source from my above git link and rest of the changes from that are based on documentation and my own ideas. CREDITS: ELAN - Arjan Opmeer for ELAN linux documentation/source FocalTech - mgottschlag (github) for linux source Synaptics - Synaptics official documentation and linux source I would like to thank the VoodooPS2 team (Slice, King, rehabman and many others who contributed to the VoodooPS2) for ideas, Apple for their PS2 open sources which i've used as base for my driver and linux sources for the touchpad initialization and packet info. SmoothMouse 1.0.5.zip mouseaccelerationpref11d.zip Apple Keyboard Layout ID.rtf ElanTouchpad_v2.8.3.zip ELAN_v3.8.5_Final_Upd.zip ELAN_v4.0.5.zip SmartTouchPad_v4.2_Final.zip SmartTouchPad_v4.3_Final.zip SmartTouchPad_v4.4_Final_64bit.zip SmartTouchPad_v4.4_Final_32_64bit.zip SmartTouchpad_v4.4.5_32_64bit.zip SmartTouchpad_v4.4.5_64bit.zip SmartTouchPad_v4.5_Final_64bit.zip SmartTouchPad_v4.6.zip SmartTouchPad_v4.6.5.zip SmartTouchPad_v4.7 beta 3.zip SmartTouchpad v4.7 beta 5.zip
  4. 5 points
    Mojave Clover Guide Warning: Follow guide at your own risk, I hold no responsibility if you brick your system or destroy all data during the process. If you're creating the installer from a real Mac, make sure you don't accidentally select the real Mac drive when installing Clover loader. It may cause your Mac to not boot again. You've been warned! New Installation BIOS: Set to Default, apply, then set SATA Operations to AHCI, set Boot List Option to UEFI, Disable Secure Boot Note: By default, upgrading or new Install of Mojave on an SSD drive, it'll automatically convert to APFS format. (1) Create the USB installer via Terminal with "createinstallmedia" (a minimum of 16GB UFD is needed or an external USB drive) sudo /Applications/Install\ macOS\ Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/"target_USB" --applicationpath /Applications/Install\ macOS\ Mojave.app --nointeraction Note: target_USB = name of the USB drive you're writing to. When done, USB Drive will automatically renamed to "Install MacOS Mojave" (2) Install Clover with following config, add appropriate Bootpack to /EFI/Clover UEFI: Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\DataHubDxe-64 Drivers64UEFI\FSInject-64 Drivers64UEFI\SMCHelper-64 Drivers64UEFI\ApfsDriverLoader-64 Drivers64UEFI\AptioMemoryFix-64 Drivers64UEFI\PartitionDxe-64 Install Clover Preference Pane Finally add to Drivers64UEFI\HFSPlus.efi (not included in Clover installer) (3) Boot with the USB installer, start Disk Utility and initialize your SSD as an APFS drive, name it "Mojave". You can partition drive now if preferred. Close Disk Utility, select Install MacOS. (4) System will auto reboot after files has been copied (5) Boot with USB installer, select "Boot macOS Install from Mojave". Installation will continue installing and reboot (Might have to do this rebooting a couple of times) (6) Boot with USB installer, finish the customization (7) Follow post install steps from Post # 1 Upgrading to Mojave Before upgrading, do the following: (1) Update to latest Clover (2) Upgrade kexts you're currently using found under /EFI/CLOVER/kexts/Other/ and kexts you have installed to /L/E or /S/L/E Common links for new kexts: https://github.com/vit9696/Lilu/releases https://github.com/vit9696/Lilu/blob/master/KnownPlugins.md https://bitbucket.org/RehabMan/ (3) Make sure it's still bootable with the above 2 updates (4) Follow this guide to update Config file and generate USBPort kext Note: Mojave, Lilu + WhateverGreen You cannot use the Clover's KextsToPatch for framebuffer patching in Mojave for Skylake and above MacOS 10.14.1+ does not work with the USB port limit patch, so best to create the USBPort kext in HS Some Mojave bootpack links: E7x70 (Skylake), might work on similar Skylake systems with some tweaks https://osxlatitude.com/forums/topic/9179-dell-latitude-e7x70-clover-uefi-only/?do=findComment&amp;comment=86790 E7x50 (Broadwell), might work on similar Broadwell system with some tweaks https://osxlatitude.com/forums/topic/8514-dell-latitude-e7450-clover-uefi-only/?do=findComment&amp;comment=86791 E7x40 (Haswell), might work on similar Haswell system with some tweaks https://osxlatitude.com/forums/topic/6472-dell-latitude-e7240e7440/?do=findComment&amp;comment=86943 /!\ When posting for HELP, please include full system specs and attach debug files. If you're not able to start the installer, then attach the Clover folder and include screenshot(s) of the error / KP by booting with verbose + debug 0x100 mode
  5. 5 points
    Clover Bootpacks I'll be adding more bootpacks when I have them confirmed working by members of this forum... Don't forget to check the Update section below (post #4) for updated files and information!!! Note: Sierra bootpacks already have the updated files listed in post #4 Note: Bootpack (EFI) consists of combining the Generic EFI + the model you're downloading!!! Instruction: 1) Download the Generic EFI folder. Generic EFI Folder EFI_r4910.zip 2) Download model below and add the contents into the Generic /EFI/Clover <- folder Latitude UEFI Only - GUID Scheme - Kabylake (OS X 10.12.6 and Up)- (See Note2 below) Sierra / High Sierra 5480_HD620_v1.6.4_HS.zip 5480_HD630-Optimus_HS.zip (BIOS 1.9.3) - Skylake (OS X 10.11.4 and Up)- (See Note2 below) El Capitan E7x70.zip - latest Sierra / High Sierra bootpack here Sierra 5480_BIOSv1.5.2.zip E5470_1.17.3_HS.zip High Sierra E5470_1.18.6_HS.zip - Broadwell - (See Note2 below) El Capitan E7450_update.zip - latest Sierra /High Sierra bootpack here E5450_HD5500.zip E5550.zip Sierra E5550_A15.zip E5550_A15_Disable_GT820M.zip E5450_HD5500_A15.zip 3450_A13.zip High Sierra E5450_HS_A19.zip - Haswell El Capitan E7440.zip E6540.zip E5540.zip E5450_HD4400.zip 3550.zip 3540.zip 3440.zip 3340.zip Sierra E7440_A20.zip E6540_Optimus_A17.zip E6540_HD4600_Only.zip E6440_A14.zip - based off Hervé's work E5540_Sierra.zip E5440_A13.zip 3550_HD4400_A12.zip High Sierra E7440_HS.zip E6440_A14_HS E5440_A21_Disable-Nvidia.zip - IvyBridge El Capitan E6230.zip - 1366x768 E6430.zip - 1600x900 and above E5530.zip - Rename Config/DSDT depending on display resolution Sierra E6530_HD4000_Only.zip 6430u_1366x768.zip - BIOS A06 See here for 6430u HiRes (1600x900) file E6430_A12.zip - check Readme.txt inside bootpack E5530_A12.zip E6330_A11.zip - check Readme.txt inside bootpack E6230_A11.zip E6230_HD3000.zip -> this has SandyBridge CPU High Sierra E6230_A11 Legacy - GUID Scheme - See Note1 below - SandyBridge El Capitan E6420.zip - 1600x900 E6x20_NVS.zip E6220.zip - 1366x768 E5420.zip Sierra E6220_A13.zip E5520_A14.zip - check Readme.txt inside bootpack E5420.zip - check Readme.txt inside bootpack E6420_HD3000_A23.zip- check Readme.txt inside ACPI/Patched folder E6420_Optimus_A23.zip - check Readme.txt inside ACPI/Patched folder E6520_Optimus_A19.zip - check Readme.txt inside ACPI/Patched folder High Sierra E6520_Disabled-NVS_HS.zip E6220_A13_HS.zip Inspiron UEFI Only - GUID Scheme - Broadwell - (See Note2 below) El Capitan 5458.zip Inspiron_5548.zip 5558_HD5500_Only.zip 5558_HD5500_DisableNvidia.zip Sierra 3543_A08.zip 5548_HD5500_Only.zip 5548_m270-Disabed_A07.zip 5558_920M-Disabled_A14.zip High Sierra 5558_920M-Disabled_A14_HS.zip - Haswell El Capitan 5558_HD4400.zip 3542.zip Sierra 3542_A12.zip High Sierra 5558_HD4400_HS.zip Precision UEFI Only - GUID Scheme - Skylake (OS X 10.11.4 and Up)- (See Note2 below) El Capitan 5510_HD530_Disabled-Nvidia.zip Sierra 5510_HD530_1.2.25.zip 7510_HD530_1.12.4.zip - (See more info here) Vostro UEFI Only - GUID Scheme - Kabylake Sierra / High Sierra Vostro_3468_Biosv01.07.00_HS.zip Vostro_3468_2.3.0_HS.zip XPS UEFI Only - GUID Scheme - Haswell Sierra / High Sierra XPS 12 9Q33_A07.zip Note1: For Exx20 (SandyBridge models), use Legacy - GUID Scheme. Not UEFI Install Clover with the following settings in 1: Prepare Bootable USB Drive step 26 above: Install Clover in the ESP Bootloader/Install boot0af in MBR CloverEFI/CloverEFI 64-bits SATA Note2: Systems with Broadwell / Skylake / Kabylake CPU such as Latitude E7450 and Inspiron 5548, you'll need to set the DVMT prealloc to 96MB in order to bypass KP and to enable full graphics with full QE/CI. For more info, see here. /!\ New Development: If you don't want to mod the BIOS as it might be difficult for some models, you could skip this step by adding 2 new kexts to /EFI/Clover/kexts/Other Lilu.kext & Whatevergreen Notes3: To prevent artifacts with HD 4000, the following models should not exceed BIOS A11. Downgrade to A02/A03 and then upgrade to A11 if it has exceeded: E6x30, E5x30 Latitude 6340U should stay at A06
  6. 4 points
    Beta1 installs in the exact same manner as High Sierra. The difference is that 10.14 requires Clover r4517 or higher to install successfully. https://github.com/Dids/clover-builder/releases So far, Ok on my Ivy Bridge/HD4000 Latitude E6230 with same EFI/bootpack as High Sierra 10.13 and Clover r4521. I made a quick and basic, not fully tuned, installation: Apple stated that Mojave will only support GPUs compatible with Metal so HD3000 and older 1st gen Intel HD graphics are effectively dropped (and there are no kexts for these). Support for Intel iGPUs now starts at Ivy Bridge HD4000. So, I won't be trying Mojave on my E6220 nor on my ancient D630 (support for nVidia Tesla architecture dropped too)... We'll see if this gets to evolve in the following beta versions but not much of a hope I guess. APFS conversion seems to be mandatory too. Despite my modification of the minstallconfig.xml file of the 1st reboot temporary installation in which I had set the ConvertToAPFS parameter to false, my target Mojave partition ended up converted! Not a problem in itself on my SSD (and APFS is reportedly Ok on mechanical HDD now) but that means a definitive goodbye to Chameleon/Enoch for the time being. Inescapable eventuality I guess... List of officially supported Mac models is as follows (as per /S/L/CoreServices/PlatformSupport.plist) MacPro6,1 iMac17,1 iMac16,2 iMac16,1 iMac15,1 iMac14,4 iMac14,3 iMac14,2 iMac14,1 iMac13,3 iMac13,2 iMac13,1 Macmini7,1 Macmini6,1 Macmini6,2 MacBookPro12,1 MacBookPro11,5 MacBookPro11,4 MacBookPro11,3 MacBookPro11,2 MacBookPro11,1 MacBookPro10,2 MacBookPro10,1 MacBookPro9,2 MacBookPro9,1 MacBook9,1 MacBook8,1 MacBookAir7,2 MacBookAir7,1 MacBookAir6,2 MacBookAir6,1 MacBookAir5,2 MacBookAir5,1
  7. 4 points
    Give this a try, replace into /EFI/Clover E5530_Mojave.zip
  8. 4 points
    Mojave Mojave Guide Bootpacks E7470_Mojave.zip Note: 1) Copy kexts in /EFI/Clover/kexts/Other/CopyToLE to /Library/Extensions. Repair permissions and rebuild cache 2) Enable this patch in Config.plist under KextsToPatch if you have: LiteOn, Plextor, or Hynix NVMe Hynix NVMe patch 10.13.x (Bit swap block size 0x10) -Syscl UPDATES Mojave 10.14.1 (18B75) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Install latest Clover prior to update Mojave 10.14.2 (18C54) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Install latest Clover prior to update Mojave 10.14.3 (18D42) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Install latest Clover prior to update Mojave 10.14.4 (18E226) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Install latest Clover prior to update
  9. 4 points
    Heya! After a lot of playing around with ASUS acpi tables I have finally come up with a SSDT that will work nearly on all ASUS laptops (Haswell or above) for reading FAN RPM, CPU TEMP and also Custom Controlling FAN. I do not have hardware below Haswell so can't test. If someone get's it working using this SSDT on machines prior to haswell. Let me and others know. Background Info: The system FAN is generally controlled by the embedded controller (EC) but there are methods in ACPI that can let you read and control your system FAN. As you might know, ASUS machines are the best for hackintosh as they have the best written ACPI code. Like, if it was HP instead of ASUS you would have to acquire a mutex object. Write a value to the EC and then release the object. But in ASUS machines there is a method that takes arguments and does this job automatically. Still. There are multiple methods in our DSDT that allow us to read and control system FAN. For example to read FAN speed, there are two ways. If you observe, the FAN speed is at offset 0x93 of EC (Use RWEverything to find out) So, when we search for Offset 0x93 in the DSDT we get a result like this: Offset (0x93), TAH0, 16, // TAH0 stands for FAN1 TAH1, 16, // TAH1 stands for FAN2 (in case your laptop has 2 fans) TSTP, 16, // TSTP stores current fan value in some bytes Note: Instead of using RWEverything if you have a look at method TACH you can see that it stores the values in TAH0 and TAH1 depending upon the Args supplied. So, searching for TAH0 or TAH1 we can see that they are located at offset 0x93 So, now we can read the value from these registers in some units and then we will have to use some formula to convert that unit to RPM. In order to find that formula, if you have a look at Method TACH in dsdt, you will see: Method (TACH, 1, Serialized) { Name (_T_0, Zero) If (ECAV ()) { While (One) { _T_0 = Arg0 If ((_T_0 == Zero)) { Local0 = TAH0 Break } ElseIf ((_T_0 == One)) { Local0 = TAH1 Break } Else { Return (Ones) } Break } Local0 *= 0x02 If ((Local0 != Zero)) { Divide (0x0041CDB4, Local0, Local1, Local0) Return (Local0) } Else { Return (Ones) } } Else { Return (Ones) } } So, we know that we have to store the value from TAH0 or TAH1 (depends on Arg0) and then we have to multiply it by 2 and then we have to divide it by 0x0041CDB4 (4312500) to get the value in RPMs. Once we know that, we could write a simple ACPI code to return the value in RPMs like: // GRPM means get RPM Method (GRPM, 0) { // Store value in Local0 Local0 = \_SB.PCI0.LPCB.EC0.TAH0 // If local0 is not equal to 0 If (Local0 != 0){ // Multiply by 2 Local0 = Local0 * 2 // Divide by 4312500 Divide (0x0041CDB4, Local0, Local1, Local0) } // Return the value Return (Local0) } As you can see this is very expensive method. But what we learned here is, If we execute method TACH with Arg0 as 0 (Zero) it will give us the speed in RPM of FAN 1. Similarly, if we use Arg0 as 1 (One) it will return the value in RPM for FAN 2 My laptop only has one FAN so, I can execute method TACH like, \SB.PCI0.LPCB.EC0.TACH(0) // Using Arg0 as Zero for FAN 1 And it will give me FANs RPM, so, instead of reading from EC and converting bits to RPM this is more preferable. Also, EC bytes may change while patching DSDT so it is a good idea to use dynamic methods so that a single SSDT could work for all machines. One such example is, If you use ACPIBatteryManager then you will have to convert 16bits registers to 8bits. And then, to use that "reading RPM from EC method you will have to create a new method to combine 2 8 bits registers to 1 16 bit like, // JEBR = Join 8 bit registers Method (JEBR, 2) { Return ((Arg0 | (Arg1 << 8))) // Arg0 and Arg1 will be 8Bit register 1 and 2 respectively (AH00, AH01) } Now moving to FAN control, If you have a look at method QMOD in DSDT: Method (QMOD, 1, NotSerialized) { If ((Arg0 == Zero)) { Return (Zero) // If arg0 is Zero. Terminate by returning 0 } If ((Arg0 == One)) { ^^PCI0.LPCB.EC0.ST98 (QFAN) // Hmm, ST98 is somewhat related to FAN control } If ((Arg0 == 0x02)) { ^^PCI0.LPCB.EC0.ST98 (0xFF) // Okay, ST98 again.. Something is interesting } Return (One) } Now, if you look at ST98 you can see: Method (ST98, 1, Serialized) { If (ECAV ()) // Checked if EC is available, will you write to it? { Acquire (MU4T, 0xFFFF) // Oh! So you are acquiring a mutex object CMD = 0xFF EDA1 = 0x98 EDA2 = Arg0 // Oh, so you did write Arg0 in EDA2 (Located in EC01 OperationRegion) ECAC () Release (MU4T) // Released it here, you did write something to the EC for sure Return (Zero) } Return (Ones) } Now, we can understand that, method QMOD (Quiet Mode?) Takes 1 argument that could be (0, 1 or 2). We can eliminate 0 as when we pass Arg0 as 0 it simply returns. Interesting are args 1 and 2 When using 1 it passes Arg0 to ST98 as QFAN's value (Hmm.. What is this QFAN) When using 2 it passes Arg0 to ST98 as 0xFF (255) (Oh wait! according to ACPI spec, 255 is max allowed FAN value.) Gotcha! We can use ST98 and pass it an arg ranging between 0x0 (0) to 0xFF (255) where 0 is for FAN off and 255 is for Max allowed or auto. But, why is there a QMOD method then? There might be some good reason for that. So, we will not invoke ST98 directly but will use the modus operandi of method QMOD Like, we will first store that max allowed FAN value in QFAN Then, we will invoke QMOD with Arg0 as 1 (One). Which will invoke ST98 for us hence, setting the max allowed speed for FAN. So, the ACPI code for this would be: Method (SETR, 0) { QFAN = 200 // Suppose we want to use max allowed value as 200 // Now we can call QMOD with Arg0 as 1 QMOD (1) } Now we know what to do. We now just need to write a method that can calculate the CPU temperature and then set FAN RPM accordingly. This is when you will use my SSDT-FAN How to implement: Requirements: FakeSMC kext along with sensors installed at /L/E or /S/L/E (DO NOT INJECT USING CLOVER) ACPIPoller.kext HWMonitor for monitoring CPU Temp and FANS My SSDT-FAN.aml Installation: Place SSDT-FAN.aml to /EFI/CLOVER/ACPI/patched (If using sorted order make sure you add SSDT-FAN to it) Install ACPIPoller to /L/E or /S/L/E (not both and definitely do not inject using CLOVER) Configuration: You can set "Name (UCFC, One)" to "Name (UCFC, Zero)" in my SSDT-FAN in case you want to use default FAN control method as provided by your OEM. My SSDT will only provide FAN RPM reading and CPU Temp reading.Achievements: Default scaling that ASUS provided was from 2200RPM to 2900RPM (Fan spinning fast without use) I managed to bring scale it from 255RPM to 5026RPM (Fan turns off if temp Temp rarely goes above 53˚C (Went up to 68 earlier) Technicalities: As we know know how to implement custom fan control using various methods in our DSDT we can't really use them as is in real life scenarios as FAN will literally be dancing. You might have observed that temperature keeps fluctuating a few degrees every second while you are working on something. Moreover, we need an automated method that can read and set FAN RPM. So, my SSDT calculates average temperature and then also waits for 2 seconds (to handle fluctuation) before increasing the RPM and waits for 5 seconds (to let CPU cool) before lowering RPM. You can edit this timeout by editing "Name (FCTU, 2)" for FanControlTimeoutUp and "Name (FCTD, 5)" for FanControlTimeoutDown. Method to calculate average accredited to RehabMan as he wrote the code first. There is only one known way to calculate average in maths. LOL. If you want to know how it is implemented, read this code: Note: This code is a part of my single optimizer SSDT project for ASUS laptops (Means, I am working on a single SSDT that you could place in your CLOVER/ACPI/patched and will have everything working without patching DSDT. You can customize SSDT using Device ANKD (A Nick's Device) like you can configure this SSDT to use custom FAN control or not). You can have a look at WIP code here // SSDT for FAN readings and custom FAN control for ASUS laptops // Copyright, black.dragon74 <www.osxlatitude.com> // Please configure the options in Device ANKD before compiling this SSDT DefinitionBlock("SSDT-FAN", "SSDT", 2, "Nick", "AsusFan", 0) { // Declare externals External (\_SB.QFAN, FieldUnitObj) External (\_SB.ATKD.QMOD, MethodObj) External (\_SB.PCI0.LPCB.EC0.ECAV, MethodObj) External (\_SB.PCI0.LPCB.EC0.ECPU, FieldUnitObj) External (\_SB.PCI0.LPCB.EC0.ST83, MethodObj) External (\_SB.PCI0.LPCB.EC0.ST98, MethodObj) External (\_SB.PCI0.LPCB.EC0.TACH, MethodObj) // Create a Nick's device to take care of this SSDT's configurations Device (ANKD) { Name (_HID, "ANKD0000") // Required. DO NOT change Name (UCFC, 1) // Set this to 0 if you don't wanna use my custom FAN control } // Create devices required by FakeSMC_ACPISensors Device (SMCD) { Name (_HID, "FAN0000") // Required, DO NOT change // Add tachometer Name (TACH, Package() { "System FAN", "FAN0" }) // Add CPU heatsink Name (TEMP, Package() { "CPU Heatsink", "TCPU" }) // Method to read FAN RPM (tachometer) Method (FAN0, 0) { // Check is EC is ready If (\_SB.PCI0.LPCB.EC0.ECAV()) { // Continue Local0 = \_SB.PCI0.LPCB.EC0.ST83(0) // Method ST83 acquires mutex and writes value to EC. O stands for FAN 1, Use 1 for FAN 2 If (Local0 == 255) { // If ST83 is 0xFF (Max fan speed) terminate by returning FAN RPM Return (Local0) } // Else, Get RPM and store it in Local0 Local0 = \_SB.PCI0.LPCB.EC0.TACH(0) // Method TACH in DSDT returns current FAN RPM in 100s, Arg0 as 0 is for FAN 1, for FAN 2, use Arg0 as 1 } Else { // Terminate, return Zero Local0 = 0 } // Return 255, 0 or Fan RPM based on conditionals above Return (Local0) } // Method to read CPU temp (CPU Heatsink) Method (TCPU, 0) { // Check if EC is ready If (\_SB.PCI0.LPCB.EC0.ECAV()) { // Then Local0 = \_SB.PCI0.LPCB.EC0.ECPU // EC Field storing current CPU temp Local1 = 60 // From DSDT If (Local0 < 128) { Local1 = Local0 } } Else { // Terminate, return Zero Local1 = 0 } // Return final CPU temp. ACPISensors take care of unit conversion. Return (Local1) } // Custom FAN table by black.dragon74 for ASUS laptops based on RehabMan's idea // Quietest fan operation yet coolest CPU. // Scaling from values as low as 255 RPM to values as high as 5026 RPM (That's great!) // Scaling that ASUS provided was from 2200 RPM to 2900 RPM (Duh!) // Temperatures. 0xFF means if temp is above 52C, let bios take control of things(auto). Name(FTA1, Package() { 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51, 52, 0xFF, }) // Fan speeds. 255(0xFF) is max/auto, 0(0x00) is for fan off Name(FTA2, Package() { 0, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 130, 140, 160, 185, 205, 225, 245, 250, 255 }) // Time out values Name (FCTU, 2) // RPM Up Name (FCTD, 5) // RPM Down // Table to keep track of past temperatures (to track average) Name (FHST, Buffer() { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }) // Size should match the count of above FTA1 and FTA2 package Name (FIDX, 0) // current index in buffer above Name (FNUM, 0) // number of entries in above buffer to count in avg Name (FSUM, 0) // current sum of entries in buffer // Keeps track of last fan speed set, and counter to set new one Name (FLST, 0xFF) // last index for fan control Name (FCNT, 0) // count of times it has been "wrong", 0 means no counter // Method to control FAN wrt TEMP // Name in ACPIPoller.kext's Info.plist should be FCPU with HID FAN0000 Method (FCPU, 0) { // If UCFC is set to 0, terminate If (\ANKD.UCFC == 0) { Return (0) } // If EC is not ready, terminate If (!\_SB.PCI0.LPCB.EC0.ECAV()) { Return (0) } Local5 = \_SB.PCI0.LPCB.EC0.ECPU // Current temperature of the CPU Heatsink If (Local5 < 128) { Local0 = Local5 // Store temperature in Local0 } Else { Local0 = 60 // As per BIOS } // calculate average temperature Local1 = Local0 + FSUM Local2 = FIDX Local1 -= DerefOf(FHST[Local2]) FHST[Local2] = Local0 FSUM = Local1 // Local1 is new sum // adjust current index into temperature history table Local2++ if (Local2 >= SizeOf(FHST)) { Local2 = 0 } FIDX = Local2 // adjust total items collected in temp table Local2 = FNUM if (Local2 != SizeOf(FHST)) { Local2++ FNUM = Local2 } // Local1 is new sum, Local2 is number of entries in sum Local0 = Local1 / Local2 // Local0 is now average temp // table based search (use avg temperature to search) if (Local0 > 255) { Local0 = 255 } Local2 = Match(FTA1, MGE, Local0, MTR, 0, 0) // calculate difference between current and found index if (Local2 > FLST) { Local1 = Local2 - FLST Local4 = FCTU } else { Local1 = FLST - Local2 Local4 = FCTD } // set new fan speed, if necessary if (!Local1) { // no difference, so leave current fan speed and reset count FCNT = 0 } else { // there is a difference, start/continue process of changing fan Local3 = FCNT FCNT++ // how long to wait depends on how big the difference // 20 secs if diff is 2, 5 secs if diff is 4, etc. Local1 = Local4 / Local1 if (Local3 >= Local1) { // timeout expired, so start setting new fan speed FLST = Local2 // Method 1 (Recommended) // Store custom fan value from table in Local5 Local5 = DerefOf(FTA2[Local2]) // Set QFAN value to that of Local5 \_SB.QFAN = Local5 // Execute QMOD with Arg0 as 1(One) to set FAN's max allowed speed to that of \_SB.QFAN \_SB.ATKD.QMOD(1) // End Method 1 // Method 2 (Works but not recommended) Uncomment the line below to use this (remember to comment lines in method 1) // \_SB.PCI0.LPCB.EC0.ST98 (DerefOf(FTA2[Local2])) // End Method 2 // Reset FAN count (Required in either methods) FCNT = 0 } } Return (1) // Return something as this is a requirement of a ACPI Method } } } Moment of joy: Problem Reporting: Attach proper problem reporting files. See How to generate proper problem reporting files Note: If you see FAN RPM = 255 and hear a lot of noise from FAN it means your FAN is running at it's maximum speed. Regards ACPIPoller.zip SSDT-FAN.zip
  10. 4 points
    High Sierra Clover Guide Warning: Follow guide at your own risk, I hold no responsibility if you brick your system or destroy all data during the process. If you're creating the installer from a real Mac, make sure you don't accidentally select the real Mac drive when installing Clover loader. It may cause your Mac to not boot again. You've been warned! New Installation Note: By default, upgrading or new Install of HS on an SSD drive, it'll automatically convert to APFS format. If you want to use APFS format, skip step 4 (1) Create the USB installer via Terminal with "createinstallmedia" (a minimum of 16GB UFD is needed or an external USB drive) sudo /Applications/Install\ macOS\ High\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/"target_USB" --applicationpath /Applications/Install\ macOS\ High\ Sierra.app --nointeraction Note: target_USB = name of the USB drive you're writing to (2) Install Clover with following config, add appropriate Sierra bootpacks Only + Generic EFI from post #2 above ( See note1 below for updating bootpack for HS if there isn't one for your model in post #2) UEFI: Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\DataHubDxe-64 Drivers64UEFI\FSInject-64 Drivers64UEFI\SMCHelper-64 Drivers64UEFI\ApfsDriverLoader-64 Drivers64UEFI\AptioMemoryFix-64 Drivers64UEFI\PartitionDxe-64 Install Clover Preference Pane Finally add to Drivers64UEFI\HFSPlus.efi (not included in Clover installer) Legacy: Install Clover in the ESP Bootloader/Install boot0af in MBR CloverEFI/CloverEFI 64-bits SATA (3) Boot with the USB installer, start Disk Utility and initialize your SSD as an APFS drive. Close Disk Utility, select Install MacOS. If you DO NOT want APFS, then select HFS+ format instead. Then Close Disk Utility and follow step 4, otherwise continue to Step 5 (4) Open the terminal (on the menu bar click Utility>Terminal), and launch this command /Volumes/"Image Volume"/"install macOS High Sierra.app"/Contents/Resources/startosinstall --volume /Volumes/"HighSierra" --agreetolicense --converttoapfs NO Note: HighSierra = name of the drive you're targeting (5) System will auto reboot after files has been copied (6) Boot with USB installer, select "Boot macOS Install from HighSierra". Installation will continue installing and reboot (Might have to do this rebooting a couple of times) (7) Boot with USB installer, finish the customization (8) Follow post install steps from Post # 1 NOTE1: Updating the Sierra Bootpack to be use for High Sierra unless there's a High Sierra bootpack already 1) Edit config.plist from Sierra Bootpack (I recommend using Clover Configurator 4.59 or newer) and activate FixHeaders option under Acpi: 2) Update USB port limit for High Sierra where applicable, if current Sierra Bootpack doesn't have it, then you don't need this. Either disable 10.12 (Red) and add 10.13 (Green - 9 or 100 Series) or modify 10.12 to 10.13 port limit Update: New USB port Limit patch for 10.13.4(5) and 10.13.6 credits to PMHeart 3) Under SMBIOS, update the definition so that Firmware Features and Firmware Feature Mask is now populated 4) [Recommended] Update the Sierra kexts under /EFI/CLOVER/kexts/Other/ Common links for new kexts: https://github.com/vit9696/Lilu/releases https://github.com/vit9696/Lilu/blob/master/KnownPlugins.md https://bitbucket.org/RehabMan/ Upgrading to High Sierra and keeping HFS+ format If you want to keep HFS+ format, run this command instead of launching the "Install MacOS High Sierra.app" /Applications/Install\ macOS\ High\ Sierra.app/Contents/Resources/startosinstall --agreetolicense --converttoapfs NO If you want to install or upgrade to a different partition/drive /Applications/Install\ macOS\ High\ Sierra.app/Contents/Resources/startosinstall --volume /Volumes/"targetdrive" --agreetolicense --converttoapfs NO Note: Repair permission and rebuild cache if you lost audio after upgrade. You must upgrade Clover, Config.plist and kexts as noted in NOTE1: Updating the Sierra Bootpack to be use for High Sierra When posting for HELP, please include full system specs and attach debug files. If you're not able to start the installer, then attach the Clover folder and include screenshot(s) of the error / KP by booting with verbose + debug 0x100 mode
  11. 4 points
    Troubleshooting Clover rebooting early If you encounter any of the bullet below and rebooted, make sure that your 1 DIMM be on slot A. OsxAptioFixDrv: Starting overrides for System\Library\CoreServices\boot.efi Using reloc block: yes, hibernate wake: no +++++++++++++++++++++++++++++++++++++++++++++++ OsxAptioFixDrv: Starting overrides for System\Library\CoreServices\boot.efi Using reloc block: yes, hibernate wake: no Error allocating 0x#### pages at 0x####... alloc type 2 Error loading kernel cache (0x9) Boot failed, sleeping for 10 seconds before exiting... OsxAptioFixDrv: Starting overrides for System\Library\CoreServices\boot.efi Using reloc block: yes, hibernate wake: no Error allocating 0x#### pages at 0x####... alloc type 2 Could not allocate runtime area Boot failed, sleeping for 10 seconds before exiting... Core Storage 1) From terminal, enter diskutil list. Note the virtual drive in red. >diskutil list /dev/disk0 (internal, physical): #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *256.1 GB disk0 1: EFI EFI 209.7 MB disk0s1 2: Apple_CoreStorage Macintosh SSD 63.5 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 /dev/disk1 (internal, virtual): #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Macintosh SSD +63.1 GB disk1 Logical Volume on disk0s2 75DADC16-4B7F-4C7D-9660-10A1C2A9FC02 Unencrypted 2) From terminal, run diskutil cs revert /dev/disk1 3) Reboot with USB Installer and select the Installed drive 4) Continue with 3. POST-INSTALLATION Credits to peluko iMessage and FaceTime https://github.com/camielverdult/Ramblings-of-a-hackintosher-High-Sierra/blob/master/iMessage.md
  12. 3 points
    @Nancy10 Try my Mojave guide here Use this bootpack, files goes into /EFI/Clover replacing the default installed by Clover Kexts in ../kext/Other/CopyToLE should be copied to /Library/Extensions after installation as part of post install. Good luck 7480_HD620.zip
  13. 3 points
    DisableTurboBoostBatery.kext doesn't work with VirtualSMC.kext and SMCBatteryManager.kext. Problem is here: void DisableTurboBoostBattery::actOnChangedPowerState() { if (pPowerSource && isOnAC != pPowerSource->externalChargeCapable() && pPowerSource->batteryInstalled()) { if ((isOnAC = pPowerSource->externalChargeCapable())) enable_tb(); else disable_tb(); } } Reason is simple - externalChargeCapable returns different values with VirtualSMC.kext and SMCBatteryManager.kext than with FakeSMC.kext and ACPIBatteryManager.kext. ExternalChargeCapable property has same value as ExternalConnected in case of FakeSMC.kext and ACPIBatteryManager.kext. On battery both values are false, on charger both values are true. With VirtualSMC.kext and SMCBatteryManager.kext only ExternalConnected property change value. It's true on charger and false on battery. ExternalChargeCapable is always true. This is the reason why disable_tb() is never called with VirtualSMC.kext and SMCBatteryManager.kext and Turbo Boost remains active. Fix should be simple as this: void DisableTurboBoostBattery::actOnChangedPowerState() { if (pPowerSource && isOnAC != pPowerSource->externalConnected() && pPowerSource->batteryInstalled()) { if ((isOnAC = pPowerSource->externalConnected())) enable_tb(); else disable_tb(); } } This should work in both usage cases - VirtualSMC.kext with SMCBatteryManager.kext and FakeSMC.kext with ACPIBatteryManager.kext. VirtualSMC implementation of ExternalChargeCapable looks proper based on documentation: ExternalConnected Type: bool IORegistry Key: kIOPMPSExternalConnectedKey True if computer is drawing external power ExternalChargeCapable Type: bool IORegistry Key: kIOPMPSExternalChargeCapableKey True if external power is capable of charging internal battery
  14. 3 points
    - First create 2 partitions Extended Journal when installing OS X. Make sure to jot down the size so you won't wipe out the wrong partition when you install Windows on it later. Hint: don't make both the same size - Use Disk Utility to prepare a Mac OS X Extended partitions (don’t ever use Fat32, Disk Utility will mess up your drive) - After installing OS X, everything all setup. Then install Windows - Create a FAT32 usb drive, extract Windows 10 64-bit iso there (done on a Windows system) - Boot to Win10 usb drive, select custom install, locate the partition that is not OS X, delete it. Then select it (unallocated space) format it to NTFS, install Windows there. - Windows will automatically boots back to Windows. Install all drivers...etc. - Now to fix the boot option - Go to BIOS, create boot option. Browse to /EFI/Clover/Cloverx64.efi, give it a Name. Now move the Clover boot entry to top. - Save and reboot. Now you'll see the option to boot Windows or OS X from the Clover GUI. To fix the time in Windows, launch regedit navigate to [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\TimeZoneInformation] create a DWORD (32 bit) value, name it RealTimeIsUniversal. Set the value to 1. Exit Boot to OSX, then reboot to Windows. You should see time is correctly sync'd up.
  15. 3 points
    Just another 1-2 weeks, and you will have updates from me sure. I am working on it as I have some issues with my dev environment right now to finish. Thanks for the patience.
  16. 3 points
  17. 3 points
    LAST UPDATED: 11 APRIL 2019 Hi all, I am very excited to finally hack this world famous GPU mining motherboard and pleased to share with you all the clover bootpack. Specification Asrock H81 BTC Pro Ver 2.0 4th Gen 3.5 GHz i3-4330 8 GB DDR3 1600 MHz Memory Intel Graphics HD 4600 HDMI output on 24-inch LED Monitor (1920 x 1080) Clover Bootpack The Clover bootpack can be downloaded from the following link: CLOVER 10.14.4.zip Support for Mac OS Majave 10.14.4 (Clover 4910) CLOVER 10.14 Beta 4.zip Support for Mac OS Mojave 10.14 Beta 4 18A326h (Clover 4586) CLOVER 10.14 Beta.zip Support for Mac OS Mojave 10.14 Beta 18A293U (Clover 4517) CLOVER 10.13.6.zip Support for Mac OS High Sierra 10.13.6 (Clover 4635) CLOVER-V4.zip Support for Mac OS High Sierra 10.13.4 (Clover 4428) Updated all kexts to latest versions CLOVER-V3.zip Support for Mac OS High Sierra 10.13.2 (Clover 4360) Updated all kexts to latest versions CLOVER-V2.zip Support for Mac OS High Sierra 10.13.1 (Clover v4293) Updated all kexts to latest versions Added IntelGraphicsFixup.kext and Shiki.kext Combined all ATI & Intel GPU configs & kexts into single bootpack for multi GPU support CLOVER-Intel.zip Support for Mac OS High Sierra 10.13.1 (Clover v4293) with Intel Graphics CLOVER-ATI.zip Support for Mac OS High Sierra 10.13.1 (Clover v4293) with ATI Graphics General Notes (1) The UEFI Bios does not detect Clover EFI natively. For first boot into Mac OS, you will need to boot Clover EFI using the Installer USB. In order to add Clover EFI into UEFI Bios, you will need to manually add it using the Clover UEFI shell using the following command:- (a) bcfg boot add 3 fsX:\EFI\BOOT\CLOVER\CLOVERX64.EFI "Clover" (You will need to replace X with the location of your Clover EFI partition. This is shown in the list when you first enter the UEFI shell) (b ) Lastly, do bcfg boot mv 3 0 to move the Clover boot order to the first. (2) I found that this motherboard is very compatible with Mac OS and patched DSDT / SSDT is not required. Notes on Mac OS Mojave 10.14.4 (1) Everything works (2) Whatevergreen.kext now autodetects the graphics card. Make sure no graphics injection is done in Clover. Notes on Mac OS Mojave 10.14 Beta 4 18A326h (1) Everything works (2) Updated from Mac OS Majave 10.14 Beta 18A293U via Software Update in the System Preference. Notes on Mac OS Mojave 10.14 Beta 18A293U (1) Everything works including sleep. (2) Dedicated GPU Radeon Pro 560 not displaying on monitor. May need to wait for WhateverGreen.kext to be updated with support for this Mac OS version. Notes on Mac OS High Sierra 10.13.1 (1) Everything works including sleep. (2) For those that need to update 10.13 to 10.13.1, you will need to install the latest clover (version 4293 is the one I used). If there are error messages, you may try to remove EmuVariableUefi-64.efi from Clover EFI temporarily, clear NVRAM using sudo nvram -c in terminal, download the update directly from apple website and install. Notes on Mac OS High Sierra 10.13.2 (1) Everything works including sleep. (2) For those updating from 10.13.1 to 10.13.2, you will need to install the latest clover and lilu including plugins (or download latest bootpack above) as well as download and install the update directly from apple website. Updating via App Store doesnt seem to work for me as I get the mkpg not found error message after reboot. Notes on Mac OS High Sierra 10.13.4 (1) Everything works including sleep. (2) For those updating from an earlier version of 10.13 to 10.13.2, you will need to install the latest clover and lilu including plugins (or download latest bootpack above) as well as download and install the update directly from apple website. The OS X installer will reboot several times. Notes on Mac OS High Sierra 10.13.6 (1) Everything works including sleep. Notes on Mining (1) As all you miners know, this motherboard can take up to six (6) GPUs, I have yet to test additional GPU on the PCIEx1 slots. At the moment, the single GPU that i'm using is installed on the PCIEx16 slot. I will test it once I have opportunity to get additional GPU. In the mean time, for those miners who already have this motherboard in their rig and are already using Windows or Linux, Mac OS may be a good OS to try since some miners (like ethereum's ethminer) are also released for Darwin and both NVIDIA and ATI have provided drivers for their latest GPUs. This does open up a good possibily of using Mac OS for GPU mining! (2) I was able to use the dedicated RX560 GPU for both as primary display as well as for mining. However, it causes the system to slow down and created artifacts when I rebooted / shutdown. I was able to make the system more stable by using the integrated HD4600 GPU as primary display and the dedicated RX560 GPU for mining. In order to use both integrated GPU and dedicated GPU, both Intel and ATI need to be injected by Clover. In the case of ethereum miner, ethminer was able to recognized all GPU but I only selected the RX560 for mining. This made the system more stable. (3) [10-11-2017] I just installed a third old AMD Radeon HD 7750 GPU on the first PCIEx1 slot and am very happy to see that Mac OS recognized it straight away. In the case of ethereum miner, ethminer was able to recognized all GPU. Attached pictures below:- 22nd December 2017 Update (4) One of my main concern is I am still not able to get HWMonitor to show GPU temperature which is very important to monitor the current health of the GPUs. We would not want the GPU to overheat due to unforeseen reasons. Let me know if you are able to solve this issue. (5) During my discussion with crew member Rhyker, we were discussing on ways to tune the GPU from within Mac OS. As you know, currently the manufacturer only provide tuning software for Windows and to a limited extend Linux. We were thinking of running Windows under a virtual machine to access the GPU tuner to tune the GPUs. However, based on my last attempt, accessing native GPU from a virtual machine is still not possible although there are projects that are attempting to do this. Let me know if this idea is workable. Let me know if the clover bootpack works for you. Credits goes to Jake Lo and Bronx Teck Cheers!
  18. 3 points
    Updates El Capitan 10.11.1 STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: None El Capitan 10.11.2 (15C50) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: None El Capitan 10.11.3 (15D21) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: None El Capitan 10.11.4 (15E65) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Upgrade to latest Clover prior to upgrade just in case New Issues: 1) KP on some systems with VoodooPS2Controller (Alps touchpad). Reboot with USB installer, select HD/SSD to boot. Remove /EFI/Clover/Kexts/Other/VoodooPS2Controller and replace it with Dr. Hurt's version R6B6 2) DummyHDA with Clover-on-the-fly patch stopped working Install new kexts for according to your CodecID Latitude Exx20 AppleHDAIDT.kext.zip Latitude Exx30 AppleHDA_IDT.kext.zip Latitude E7x40, E6540, E5440 Precision M4800, M6800 AppleHDA_ALC292.kext.zip Latitude E7x70, E7x50, E5450 Precision 7510 AppleHDA_ALC293.kext.zip Inspiron 3542, 5548, 5558, 5458 Latitude 3340, 3550 AppleHDA_ALC255.kext.zip Inspiron 5537 Latitude 3440, 3540 AppleHDA_ALC283.kext.zip Optiplex 9020 AppleHDA_ALC280.kext.zip Lenovo Z51-70 AppleHDA_ALC236.kext.zip * If your dummyHDA is not listed here and was working prior to 10.11.4, see here how to update it El Capitan 10.11.5 (15F34) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Same fix applied from 10.11.4 if you're upgrading from 10.11.3 and below or new install using provided bootpacks El Capitan 10.11.6 (15G31) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Same fix applied from 10.11.4 if you're upgrading from 10.11.3 and below or new install using provided bootpacks
  19. 3 points
    Search for PW934, that should get you the same card. For the card you have which is DW1520 to work, you can change your SMBIOS to MBA5,1 or MBA5,2, but AirDrop might not work as it doesn't work for me.
  20. 2 points
    Last update: 18 Nov 2018 'thought it would be useful to try and provide a recap of what is supported, what isn't, if it works OOB or if it does not, for which OS X version, etc. I invite everyone to bring his/her own contribution and it'll be added to the list. This post will be updated as contributions come along in order to keep the list under control. Hardware specifications can be verified here: http://wikidevi.com/wiki/Main_Page Note: OOB = Out of the Box This inventory is now limited to Mac OS X/OS X versions in the range Snow Leopard 10.6 to El Capitan 10.11. A separate inventory for macOS versions is available here. Unsupported: Vendor Model Format Ven-Dev Chip Rate SL Li ML Ma Yo Ca OOB Kext (driver) AzureWave AW-CB161H ½Min PCIe 10ec-8821 RTL8821AE A/B/G/N/AC N N N N N N - - AzureWave AW-CB209NF NGFF/M.2 10ec-8821 RTL8821AE A/B/G/N/AC N N N N N N - - Dell DW1501 ½Min PCIe 14e4-4727 BCM4313 A/B/G/N N N N N N N - - Dell DW1503 ½Min PCIe 14e4-4727 BCM4313 A/B/G/N N N N N N N - - Dell DW1504 ½Min PCIe 14e4-4727 BCM4313 B/G/N N N N N N N - - Dell DW1530 ½Min PCIe 14e4-4359 BCM43228 A/B/G/N N N N N N N - - Dell DW1540 ½Min PCIe 14e4-4359 BCM43228 A/B/G/N N N N N N N - - Dell DW1701 ½Min PCIe 14e4-4727 BCM4313 B/G/N N N N N N N - - Dell DW1704 ½Min PCIe 14e4-4365 BCM43142 B/G/N N N N N N N - - Dell DW1810 NGFF/M.2 168c:0042 QCA9377 A/B/G/N/AC N N N N N N - (=QCNFA435) Dell DW1820 NGFF/M.2 168c:003e QCA6174A A/B/G/N/AC N N N N N N - (=QCNFA344A) Intel All - - - - N N N N N N - No exception! Qualcomm QCNFA335 NGFF/M.2 168c-0042 QCA9377 A/B/G/N/AC N N N N N N - - Qualcomm QCNFA344A NGFF/M.2 168c-003e QCA6174A A/B/G/N/AC N N N N N N - - Ralink RT5390 ½Min PCIe 1814-539b RT5390 B/G/N N N N N N N - - Supported: Vendor Model Format Ven-Dev Chip Rate SL Li ML Ma Yo Ca OOB Kext (driver) Atheros AR5B91 Mini PCIe 168c-002a AR9281 B/G/N Y Y Y Y Y Y Y - Atheros AR5BXB6 Mini PCIe 168c-001c AR5424 A/B/G Y Y N N N N Y up to Lion only Atheros AR5BXB72 Mini PCIe 168c-0024 AR5418/5133 A/B/G/N Y Y Y Y Y Y N patch Atheros40 Atheros AR5BXB92 Mini PCIe 168c-002a AR9280 A/B/G/N Y Y Y Y Y Y Y - Atheros AR5BXB112 Mini PCIe 168c-0030 AR9380 A/B/G/N Y Y Y Y Y Y Y - Atheros AR5B22 Mini PCIe 168c-0034 AR94624 A/B/G/N N N N Y Y Y N FW + Atheros40 patch Atheros AR5B93 ½Min PCIe 168c-002a AR9283 B/G/N Y Y Y Y Y Y Y - Atheros AR5B95 ½Min PCIe 168c-002b AR9285 B/G/N Y Y Y Y Y Y N DSDT/Atheros40 patch Atheros AR5B97 ½Min PCIe 168c-002e AR9287 B/G/N Y Y Y Y Y Y N DSDT/Atheros40 patch Atheros AR5B195 ½Min PCIe 168c-002b AR9285 B/G/N Y Y Y Y Y Y N (=AR5B95+BT3.0) Atheros AR5B197 ½Min PCIe 168c-002e AR9287 B/G/N Y Y Y Y Y Y N (=AR5B97+BT3.0) Atheros AR5BHB92 ½Min PCIe 168c-002a AR9280 A/B/G/N Y Y Y Y Y Y Y - Atheros AR5BHB112 ½Min PCIe 168c-0030 AR9380 A/B/G/N Y Y Y Y3 Y Y Y - Atheros AR5B125 ½Min PCIe 168c-0032 AR94854 B/G/N N N N Y Y Y N FW + Atheros40 patch Atheros AR5B225 ½Min PCIe 168c-0032 AR94854 B/G/N N N N Y Y Y N FW + Atheros40 patch AzureWave AW-NB037H ½Min PCIe 168c-002b AR9285 B/G/N Y Y Y Y Y Y N (=AR5B195) AzureWave AW-NB048H ½Min PCIe 168c-002b AR9285 B/G/N Y Y Y Y Y Y N (=AR5B195) AzureWave AW-NB290H ½Min PCIe 14e4-4357 BCM43225 B/G/N N N Y Y Y Y N DSDT/Brcm4360 patch AzureWave AW-CE123H ½Min PCIe 14e4-43b1 BCM4352 A/B/G/N/AC N N Y Y Y Y N DSDT/Brcm4360 patch AzureWave AW-CB160H ½Min PCIe 14e4-43a0 BCM4360 A/B/G/N/AC N N N Y Y Y Y - Dell DW1470 Mini PCI 14e4-4319 BCM4318 A/B/G Y Y Y Y Y Y Y - Dell DW1390 Mini PCIe 14e4-4311 BCM4311 B/G Y Y Y Y2 Y Y Y - Dell DW1395 Mini PCIe 14e4-4315 BCM4312 B/G Y Y Y1 N N N N BCM43xxxFamily & v2 Dell DW1490 Mini PCIe 14e4-4312 BCM4311 A/B/G Y Y Y Y2 Y Y Y - Dell DW1505 Mini PCIe 14e4-4328 BCM4321 A/B/G/N Y Y Y Y2 Y Y Y - Dell DW1397 ½Min PCIe 14e4-4315 BCM4312 B/G Y Y Y1 N N N N (=DW1395) Dell DW1502 ½Min PCIe 168c-002b AR9285 B/G/N Y Y Y Y Y Y Y (=AR5B95) Dell DW1506 ½Min PCIe 168c-0032 AR94854 B/G/N N N N Y Y Y N (=AR5B125) Dell DW1510 ½Min PCIe 14e4-432b BCM4322 A/B/G/N Y Y Y Y Y Y Y - Dell DW1515 ½Min PCIe 168C-002a AR9280 A/B/G/N Y Y Y Y Y Y Y (=Atheros xB92) Dell DW15205 ½Min PCIe 14e4-4353 BCM43224 A/B/G/N N N Y Y Y Y Y/N MBA5,2/Brcm4360 patch Dell DW1550 ½Min PCIe 14e4-43b1 BCM4352 A/B/G/N/AC N N Y Y Y Y N DSDT/Brcm4360 patch Dell DW1601 ½Min PCIe 168c-0034 AR94624 A/B/G/N/AD N N N Y Y Y N (=AR5B22) Dell DW1702 ½Min PCIe 168c-002b AR9285 B/G/N N N N Y Y Y N (=AR5B195) Dell DW1703 ½Min PCIe 168c-0032 AR94854 B/G/N N N N Y Y Y N (=AR5B225) Dell DW1705 ½Min PCIe 168c-0036 AR95654 B/G/N N N N Y Y Y N FW + Atheros40 patch Dell DW1560 NGFF/M.2 14e4-43b1 BCM4352 A/B/G/N/AC N N Y Y Y Y N DSDT/Brcm4360 patch Dell DW1707 NGFF/M.2 168c:0036 AR95654 B/G/N N N N Y Y Y N FW + Atheros40 patch Dell DW1802 NGFF/M.2 168c-0034 AR94624 A/B/G/N N N N Y Y Y N (=AR5B22) Dell DW1820A NGFF/M.2 14e4-43a3 BCM4350 A/B/G/N/AC N N N N Y Y ? Expected OOB Dell DW1830 NGFF/M.2 14e4-43ba BCM43602 A/B/G/N/AC N N N Y Y Y Y OOB from Yosemite Asus USB-N10 USB 2.0 0b05-1786 RTL8188SU B/G/N Y Y Y Y ? ? N RealTek's v2.0.1 Asus USB-AC51 USB 2.0 0b05-17d1 MT7610U A/B/G/N/AC Y Y Y Y ? ? N Asus's driver CSL Nano V.2 USB 2.0 0bda-8176 RTL8188CUS B/G/N Y Y Y Y ? ? N RealTek's v2.0.1 D-Link DWA-121 A1 USB 2.0 2001-3308 RTL8188CUS B/G/N Y Y Y Y ? ? N RealTek's v2.0.1 Lafalink LF-D10 Nano USB 2.0 148f-7601 MT7601 B/G/N Y Y Y Y Y Y N Ralink's v4.2.9.10 Lafalink LF-D12 Nano USB 2.0 148f-5370 RT5370 B/G/N Y Y Y Y Y Y N Ralink's v4.2.9.2 NetGear WNA3100M USB 2.0 0846-F001 RTL8192CU B/G/N Y Y Y Y Y Y N Realtek's v2.0.1 On-Nwrks N300 USB 2.0 0846-F001 RTL8192CU B/G/N Y Y Y Y Y Y N Realtek's v2.0.1 Tenda W522U USB 2.0 148f-3572 RT3572 A/B/G/N Y Y Y Y Y Y N Ralink's v4.2.9.2 TP-Link TL-WN723N v3 USB 2.0 0bda-8179 RTL8188EUS B/G/N Y Y Y Y Y Y N TP-Link's driver TP-Link TL-WN725N v2 USB 2.0 0bda-8179 RTL8188EUS B/G/N Y Y Y Y Y Y N TP-Link's driver TP-Link TL-WN823N v1 USB 2.0 0bda-8178 RTL8192CU B/G/N ? Y Y Y Y Y N TP-Link's driver TP-Link TL-WN823N v2 USB 2.0 2357-0109 RTL8192EU B/G/N Y Y Y Y Y Y N TP-Link's driver Asus USB-AC56 USB 3.0 0b05-17d2 RTL8812AU A/B/G/N/AC Y Y Y Y ? ? N Asus's driver Asus PCE-AC66 PCIe x1 14e4-43a0 BCM4360 A/B/G/N/AC N N N Y Y Y Y - Asus PCE-AC68 PCIe x1 14e4-43a0 BCM4360 A/B/G/N/AC N N N Y Y Y Y - TP-Link TL-WN781ND v1 PCIe x1 168c-002b AR9285 B/G/N Y Y Y Y Y Y N DSDT/Atheros40 patch TP-Link TL-WDN4800 PCIe x1 168c-0030 AR9380 A/B/G/N Y Y Y Y Y Y Y - TP-Link Archer T9E PCIe x1 14e4-43a0 BCM4360 A/B/G/N/AC N N N Y Y Y Y - NB: Patching means adding the PCI ids of the listed card to the Info.plist file found inside the listed kext. In rare cases, binary patching may also be necessary. For some cards, DSDT Patching can be a suitable and permanent alternative to kext patching (no need to repatch a kext after OS X updates and upgrades or new installations). For instance, in the case of the Atheros AR5B95 card (chip AR9285 168c,2b), adding compatibility with a chip known to be supported OOB such as AR9380 168c,30 or AR9280 168,2a (as found in the vanilla Atheros40 kext) in a _DSM method for the identified DSDT device does the trick once and for all since it'll make the OS load the associated kext: Device (<YourDevice>) // Identified wireless device through IORegistryExplorer (usually: ARPT) { ... ... ... Method (_DSM, 4, NotSerialized) // Device Specific Method for the wireless card { Store (Package () { "model", Buffer (0x1E) { "Atheros AR5B95 b/g/n Wireless" }, "device_type", Buffer (0x08) { "AirPort" }, "built-in", Buffer (One) { 0x00 }, "name", Buffer (0x10) { "AirPort Extreme" }, "AAPL,slot-name", Buffer (0x09) { "Internal" }, "compatible", // Declares compatibility with a device Buffer (0x0B) { "pci168c,30" // PCI id of device supported OOB } }, Local0) DTGP (Arg0, Arg1, Arg2, Arg3, RefOf (Local0)) Return (Local0) } } ` In the same respect, in the case of the Broadcom BCM4322x cards (e.g.: chip BCM43225 14e4,4357), adding compatibility with a chip known to be supported OOB such as BCM94360 14e4,43ba or 14e4,43a0 (as found in the vanilla AirPortBrcm4360 kext) in a _DSM method for the identified DSDT device does the trick once and for all since it'll make the OS load the associated kext: Device (<YourDevice>) // Identified wireless device through IORegistryExplorer (usually: ARPT) { ... ... ... Method (_DSM, 4, NotSerialized) // Device Specific Method for the wireless card { Store (Package () { "model", Buffer (0x23) { "AzureWare AW-NB290H b/g/n Wireless" }, "device_type", Buffer (0x08) { "AirPort" }, "built-in", Buffer (One) { 0x00 }, "name", Buffer (0x10) { "AirPort Extreme" }, "AAPL,slot-name", Buffer (0x09) { "Internal" }, "compatible", // Declares compatibility with a device Buffer (0x0B) { "pci14e4,43a0" // PCI id of device supported OOB } }, Local0) DTGP (Arg0, Arg1, Arg2, Arg3, RefOf (Local0)) Return (Local0) } } ________________ 1 issues with 10.8.4/10.8.5: med/high-secured networks (eg: AES) unsupported, only clear/low-secured (eg: WEP) networks supported. For ML, revert to pre-10.8.4 airportd file to fix issue and apply following Terminal commands: sudo chmod 755 /usr/libexec/airportd sudo chown 0:0 /usr/libexec/airportd xattr -d com.apple.quarantine /usr/libexec/airportd Pre-ML10.8.4 airportd.zip 2 issues with 10.9: secured networks (eg: AES (& WEP?)) unsupported, only clear (& WEP?) networks. ML fix not successful, so no fix available yet. According to forum member javamocha2000, DW1390 and DW1505 both operate OOB under Mavericks with WPA2-PSK encryption. 3 Some BCM4311-based cards with PCI id 14e4-4311 and some Atheros AR9380-based cards are reported non-functional -> the affected devices are half-size mini PCIe models, full-size mini PCIe models being Ok. 4 AR946x (168c,34), AR9485 (168c,32) and AR9565 (168c,36) work to some degree (i.e. not 100%) with alternative (re-written) Atheros40 driver as posted at InsanelyMac by Chunnann. Further patching facility posted here. These cards are NOT recommended. 5 DW1520 (14e4,4353) is known to suffer from frequent and repeated wireless disconnections when plugged into mini PCIe-only slot and built-in Bluetooth is enabled. This may even lead to wireless turning off. This has been noticed on Dell Latitude E6x20 and E6x30. Wireless works Ok once built-in Bluetooth is disabled in BIOS or, as stated by wl_michael, if the card is fitted into combo PCIe/USB slot such as WWAN.
  21. 2 points
    Hello everyone, Little background information about firmware patch from linux: I've developed this kext to update the firmware needed for those Atheros AR3012 and Broadcom Bluetooth devices to work with all functionalities that hardware supposed to do. Also integrated support for the Atheros bluetooth AR3011 (from old kext by mac4mat) with some improvements/fixes in my kext to make a single solution for bluetooth. BUG REPORT (HAVE A PROBLEM?): Send me your system log file from /var/log, ioreg file saved using IORegistryExplorer app v2.1 and Sys info saved from the app System Information (found in Utilities) in File menu. To receive files from other bluetooth devices (like Mobiles), enable the option "Bluetooth Sharing" in System Preferences->Sharing. Want to know why you can't pair iPhone? Read here Your Combo card WiFi hardware is detected and working, but Bluetooth hardware was not detected in ioreg and not working ? Read this post (Credits: tomwho) Following are the Bluetooth cards supported by my kext: AR3011: Atheros AR5B195 Combo (AR9285 Wifi + AR3011 Bluetooth) Atheros AR5B197 Combo (AR9287 Wifi + AR3011 Bluetooth) Other Atheros AR3011 cards with ids list below AR3012: Atheros WB225 Combo (AR9485 Wifi(doesn't work) + AR3012 Bluetooth) Other Atheros AR3012 cards with ids list below Atheros AR3011 30 sec delay fix (or) after sleep issues patch: (Should be working in 10.9.1+) Enter the following two commands in terminal and reboot: sudo perl -pi -e 's|\x0F\x85\x07\x01|\x0F\x84\x07\x01|g' /System/Library/Extensions/IOBluetoothFamily.kext/Contents/PlugIns/IOBluetoothHostControllerUSBTransport.kext/Contents/MacOS/IOBluetoothHostControllerUSBTransport sudo touch /System/Library/Extensions/ For Clover, add this to kext patches instead: Name: IOBluetoothHostControllerUSBTransport Find: 0F850701 Replace: 0F840701 Comment: Fix Bluetooth 30 seconds delay patch Credits to TimeWalker for the patch idea. NOTE: BCM4352 WiFi 5Ghz access is now working (Credit goes to SKVO fromapplife.ru. For complete details on making this WiFI card work, follow this thread: BCM4352 WiFi BROADCOM WiFi/BT Combo cards Bluetooth: Broadcom BCM4352 Combo Broadcom BCM4360 Combo Broadcom BCM43162 Combo Broadcom BCM4313 Combo (Not all cards need Update) BROADCOM USB/Integrated Bluetooth: Asus BT-400 USB Bluetooth Belkin 20702 USB Bluetooth USB Dongles with 20702A1 Bluetooth (Delock, IOGear etc.,) HP BRCM1043 Integrated Bluetooth (found in HP Elite Notebooks) Supported Bluetooth Vendor and Product ID: (Few device ids below work only from v2.8) Broadcom: VID: 13d3 PID: 3404 (Azurewave 4352) VID: 13d3 PID: 3413 (Azurewave 4360) VID: 13d3 PID: 3418 (Azurewave 4352) VID: 13d3 PID: 3435 (Azurewave 4352) VID: 13d3 PID: 3456 (Azurewave 4352) VID: 0b05 PID: 17cb (Asus USB) VID: 0b05 PID: 17cf (Asus 4352) VID: 0b05 PID: 180a (Asus 4360) VID: 050d PID: 065a (Belkin) VID: 13d3 PID: 3411 (Dell Alienware 4352) VID: 413c PID: 8143 (Dell DW1550 4352) VID: 0a5c PID: 216f (Dell DW1560 4352 NGFF) VID: 0a5c PID: 21e1 (HP Elite NB) VID: 0a5c PID: 21fb (HP 4352) VID: 0a5c PID: 216b (HP 4352 NGFF) VID: 0a5c PID: 216e (HP BCM43162 NGFF) VID: 0a5c PID: 21fd (Generic 4352) VID: 0a5c PID: 21de (4352) VID: 0a5c PID: 22be (4352/4360) VID: 04ca PID: 200a (LiteOn 4352) VID: 04ca PID: 200b (LiteOn 4352) VID: 04ca PID: 200c (LiteOn 4352) VID: 04ca PID: 200f (LiteOn 4352) VID: 0a5c PID: 21e6 (ThinkPad NB) VID: 0489 PID: e079 (Lenovo BCM43162 NGFF) VID: 0489 PID: e07a (Lenovo NGFF) VID: 0930 PID: 0223 (Toshiba NGFF) VID: 0930 PID: 0221 (Toshiba) VID: 0a5c PID: 21e8 (Dongles Delock, IOGear etc.,) VID: 0489 PID: e032 (BCM4313) AR3011: VID: 03f0 PID: 311d VID: 0489 PID: e027 VID: 0489 PID: e02c VID: 0489 PID: e03d VID: 0930 PID: 0215 VID: 0b05 PID: 179c VID: 0cf3 PID: 3000 VID: 0cf3 PID: 3002 VID: 0cf3 PID: 3005 VID: 13d3 PID: 3304 VID: 04f2 PID: aff1 VID: 04ca PID: 3002 AR3012: VID: 0489 PID: e056 VID: 0489 PID: e036 VID: 0489 PID: e03c VID: 0489 PID: e078 VID: 04ca PID: 3005 VID: 04ca PID: 3006 VID: 0cf3 PID: 311d VID: 0cf3 PID: 0036 VID: 0cf3 PID: 3004 VID: 0cf3 PID: 3010 VID: 0cf3 PID: e004 VID: 13d3 PID: 3362 VID: 13d3 PID: 3402 VID: 13d3 PID: 3474 VID: 0b05 PID: 17d0 Kext Customization: You can customize the kext for choosing firmware by editing the file "info.plist" located inside my kext "BTFirmwareUploader.kext/Contents/". Go to the section "IOKitPersonalities" and edit the entry which has your vendor and device id values. Atheros AR3011 and AR3012 BT: You can choose firmware from either linux (or) windows. (Linux firmware is recommended mostly) For Linux firmware, edit the plist entry "Use Linux fw" to Yes (or) true. ) For the Windows firmware, edit the plist entry "Use Linux fw" to No (or) false for both AR3011 & AR3012. For AR3011, you can also choose three firmwares from windows by editing the plist entry "Windows fw" to the values 0-2. Value '0' is the most recent firmware. [Note: Only Windows firmware 1 supports Fn key toggle for BT Off/on in Asus] Broadcom BT: Firmware to use: You can choose either firmware which is meant for that specific device (or) higher version available so far by editing the plist entry "DeviceSpecificFw" to Yes/No (or) true/false. You can abort (or) ignore subsequent firmware updates if the last update was failed by editing the plist entry "AbortOnFwUpdFail" to Yes/No (or) true/false. This is optional and its meant only in case if any system needed update process to continue even if last update was failed for success.(Available from v3.0.5) How to install: 1) Remove any patched kexts (or) Bluetooth enablers installed for Bluetooth and use Apple vanilla Bluetooth kext. 2) Install my kext (BTFirmwareUploader.kext) using your favorite kext installers to /System/Library/Extensions. (Don't install my kext through E/E (or) clover injection). Supports: ​Atheros BT is supported from 10.6.8 or later Broadcom BT is supported from 10.8.5 or later NOTE for 10.11: If you have any problems with my kext firmware update for Broadcom BT in 10.11 then use only "BluetoothDevBroadcomInjector.kext" instead which is just an injector to load Apple BT driver. Change Log: Update: v3.1 5 Released (Legacy version is for 10.10 or lower) Added support for new device ​Supports for 10.6.8 ​Fixed legacy version which was not working Some Minor bug fixes and optimizations Update: v3.1 (Legacy version is for 10.10 or lower) Updated non-device specific firmware version to latest available Added support new devices (check the updated list) Improved 10.11 support Some Minor bug fixes and optimizations Update: v3.0.5 Released Fixed a major bug affecting Atheros Bluetooth Improved 10.11 support Added a plist option for Broadcom Bluetooth to abort update process on fail (Optional) Some Minor bug fixes and optimizations Update: v3.0 Updated support for 10.11 using new SDK and USB API (you have to use kext compiled for 10.11) Made several Improvements and optimizations Fixed some minor bugs Update: v2.8.7 Added OS X detection to prevent/solve issues in 10.11 Fixed some bugs and made few improvements Update: v2.8.5 Fixed a major bug affecting some asus systems with KP Fixed issues related to firmware not getting updated sometimes Fixed some bugs in Atheros firmware update Added few new Atheros AR3012 bluetooth device ids to supported list Some improvements and code optimizations Update: v2.8 Updated firmware for some devices and higher version option Added support for some new devices Improvements to upload process time which finishes quicker now as i've reduced the time needed by doing more beta tests so works better Some minor bug fixes and optimizations Update: v2.7 Updated firmware for some devices and higher version option Added support for some new devices Fixes a bug when dual booting from windows which breaks BT Fixed a bug in BluetoothDevInfo kext injection and renamed the kext name Removed unnecessary "UpdAfterSleep" option from plist Some minor bug fixes and optimizations Update: v2.6 Added support for new Broadcom bluetooth devices Added support for new Atheros bluetooth devices Updated kext to use firmware specific to the Broadcom BT devices Removed unnecessary patch for HP BT (PID:21e3) Fixed some bugs Optimized code Update: v2.5.2 Final Added support for two Broadcom bluetooth devices from HP(VID: 0a5c PID: 21e3/PID: 21e1) Fixed a minor bug in BluetoothDevInfo kext Update: v2.5 Final Added plist option "UseStandaloneFw" to choose standalone firmware meant for BT only cards like Asus BT-400. Added support for two new BCM4352 BT (Dell alienware BCM4352 combo) Fixed device reset error bugs Some minor bug fixes and optimizations Update: v2.4 ​Added support for two new AR3011 BT(VID: 0489 PID: e02c and VID: 0930 PID: 0215) Added support for two new BCM4352 BT (HP and NGFF Toshiba) Added support for new AR3012 BT (VID: 0cf3 PID: 311d) Minor optimizations Update: v2.3 Improved performance of upload ​Fixed issues related to BCM Fixed issues related to firmware update after sleep Updated Broadcom firmware to new version Added LiteOn BCM4352 and an AR3011(PID: e027) card Moved bluetooth info to a plugin kext located inside the PlugIns folder Optimized code Update: v2.1 Added fully working support for AR3012 Updated new firmware in Broadcom Added Dell DW 1550 BCM 94352HMB card and AR3012 card ID's Fixed an issue with AR3011 bluetooth Optimized code Update: v2beta Added experimental support for AR3012(still in testing phase) Added firmware option for Broadcom and updated to new firmware Added new firmware for Atheros Added Asus BCM4352 card support Fixed an issue with AR3011 bluetooth which is failing for some cards like (dev:0x3000 & 0x179c) Apple bluetooth kext patch is not needed for Broadcom bluetooth anymore Update: v1.5 Added more Atheros Bluetooth devices (VEN:0cf3, DEV:3000,3002,3005) Fixed an issue with Atheros AR3011 Bluetooth after sleep Fixed an issue with Broadcom Bluetooth which prevented successful system boot without -v flag First release: v1.3 Enables Bluetooth in the new ac Broadcom BCM4352 card Added support for AR3011 from old kext(credits: mac4mat) Fixes an issue for AR3011 with the old uploader kext which is breaking during reboots in Asus Notebooks Added options to choose firmware for Atheros Bluetooth in the plist For any support, PM me in forums. Note: Don't mirror my kext please, just provide the link for my post. Credits: Leon for providing the opportunity & testing the kext, donators who helped to get me a card for the development, mac4mat (tonycrapx) for the AR3011 source and laloch(archlinux) for the ideas of Broadcom card PS: I've worked very hard in this and need your support , so I request you to consider a small donation if possible which helps me and allows to spend more time on this for future updates. Paypal: Thanks for the support. BTFirmwareUploader_v2.7_Final.zip BTFirmwareUploader_v2.8_Final.zip BTFirmwareUploader_v2.8.5_Final.zip BTFirmwareUploade_v2.8.7.zip BTFirmwareUploader_v3.0_Final.zip BTFirmwareUploader_v3.0_Final_10.11.zip BluetoothDevBroadcomInjector.kext.zip BTFirmwareUploader_v3.0.5.zip BTFirmwareUploader_v3.0.5_10.11.zip BTFirmwareUploader_v3.1_Legacy.zip BTFirmwareUploader_v3.1.zip BTFirmwareUploader_3.1.5_10.11.zip BTFirmwareUploader_3.1.5_Legacy.zip
  22. 2 points
    @MrJonesIII Download AppleALC.kext + Lilu.kext and place into /EFI/Clover/kexts/Other In Config file, change Devices/Audio, change Inject from 1 to 5, under ACPI, enable FixMutex
  23. 2 points
    Try replace AppeALC.kext with this one. Test layout-id 5, 11, 13, 21, and 56 AppleALC-1.3.6.zip
  24. 2 points
    I made that update Hervé after @Virtus confirmed it's working. I noticed the other Lenovo also has the same ID, so I added them.
  25. 2 points
    Virtualsmc.efi driver is only needed for filevault. for normal booting all you need is virtualsmc.kext in clover/kext/other folder. if you are not using fakesmc.kext.
  26. 2 points
    @saleemsss2000 Off topic please open new thread and include full specs.
  27. 2 points
    @chabkhaled1960 Yes, but your wifi is not supported @mtpiplod Copy the files from the USB to the internal drive
  28. 2 points
    That's normal in Hackintosh for those brief seconds. Lilu.kext + Whatevergreen will remove some but not 100%. If you boot with verbose mode, you won't see it, so take your pick.
  29. 2 points
    No need to patch the kext or DSDT. Add Arbitrary under Devices in Config file. You just need to determine the PCIAddr by looking at the IOReg file under RPxx/PXSX, search for pcidebug. In this example it's RP01/PXSX@0, pcidebug = 01:00:00 You can also use dspci (app attached below) to find the address Change the PCIAddr accordingly If the card reader is not on this list, it might not be supported by this patch dspci.zip
  30. 2 points
    Thank you for your contribution here. Sorry to see you go. I, too, have a few MacBook Pro's but that doesn't stop me from being here. It's a hobby and I have fun so...I think we'll be seeing you around. If not, good luck. Cheers!
  31. 2 points
    did you use all the different boot -arg after each reboot and insert the USBs? ie. boot flags (-uia_exclude_ss -uia_exclude_hs uia_include=x)
  32. 2 points
    Looks like your'e using my hot patched bootpack but not following my install guide. In /EFI/Clover/drivers64UEFI, remove everything except the following: Drivers64UEFI\DataHubDxe-64 Drivers64UEFI\FSInject-64 Drivers64UEFI\SMCHelper-64 Drivers64UEFI\ApfsDriverLoader-64 Drivers64UEFI\AptioMemoryFix-64 Drivers64UEFI\PartitionDxe-64 Drivers64UEFI\HFSPlus
  33. 2 points
    1) To fix boot issue, go to BIOS, enable Legacy Option ROMs 2) Best to install internal wifi - DW1560 is my recommendation 3) In Config file, under Boot, change Default Boot Volume to what you name your MacOS SSD (case sensitive I think). 4) Right click "install MacOS High Sierra.app" , select show package contents Go to Contents/SharedSupport, mount BaseSystem.dmg Go to /S/L/E, grab AppleHDA and replace it back to your running MacOS /S/L/E folder Repair permissions and rebuild cache
  34. 2 points
    Specifications: Model : Acer Predator Helios 300 (G3-572, 73FH) Processor : Intel® Core™ i7-7700HQ processor Quad-core 2.80 GHz Graphics Processor(GPU) : Intel® UHD Graphics 630 & NVIDIA® GeForce® GTX 1050 with 4 GB Dedicated Memory Chipset : Intel® Intel Sunrise Point HM175 Express Chipset (Kaby Lake-H) Hard disk : WDC WD10SPZX-21Z10T0 (1 TB, 5400 RPM, SATA-III) SSD disk : HFS128G39TND-N210A (128 GB, SATA-III) & Samsung 860 Evo (500GB, SATA-III) RAM : SK hynix 8GB RAM DDR4 PC19200 (2400Mhz) Wifi : Qualcomm Atheros QCA61x4A Wireless Network Adapter Bluetooth : Qualcomm Atheros (0x04ca, 0x3016) Ethernet : Realtek RTL8168/8111 PCI-E Gigabit Ethernet Adapter Audio : Realtek® High Definition Audio ALC255 USB 3.0 : Intel Sunrise Point PCH - USB 3.0 xHCI Controller Touchpad : Elan Touchpad I2C (ELAN0501) Webcam : HD Webcam Card reader : Realtek RTS5287 PCI-E Card Reader Monitor : AU Optronics B156HAN06.1 15.6" LCD (FHD: 1920 x 1080, 142 ppi) Battery : 4Cells 3220 mAh 9 Hour Interface : 1 x combo jack (Headphone-out/Microphone-in) 1 x USB 3.0 port(s) 2 x USB 2.0 port(s) 1 x RJ45 LAN Jack for LAN insert 1 x HDMI Working: Graphics with QE/CI on Intel HD630 GPU Touchpad Audio all input/output (combojack too) Keyboard Backlit Bluetooth Ethernet USB2.0 and USB3.0 Webcam Battery Indicatot Elan Touchpad with Multi touch CPU power management Sleep and Wake with Close and Open LID Fn Hotkeys Not working: Nvidia GTX 1050 Ti (Optimus not supported in hack) HDMI (port is connected to Nvidia GPU) WIFI (Atheros QCA61x4A is supported ) Issues: None BIOS Settings: BIOS Version : v1.21 Bios Settings : Main => Touchpad => Advance Main => FastBoot => Disabled Boot => Secure Boot => Disabled For Installation: 1. use createinstallmedia command : sudo /Applications/Install\ macOS\ Mojave.app/Contents/Resources/createinstallmedia --volume /Volumes/USB --nointeraction note : my usb name is USB change it with yours (usb name) 3. Install latest clover Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\DataHubDxe-64 Drivers64UEFI\FSInject-64 Drivers64UEFI\ApfsDriverLoader-64 Drivers64UEFI\AptioMemoryFix-64 Drivers64UEFI\PartitionDxe-64 Drivers64UEFI\UsbKbDxe-64.efi Drivers64UEFI\UsbMouseDxe-64.efi Install Clover Preference Pane 4. Download and copy files to EFI partition Acer-Predator_G3-572_Mojave.zip NOTE : always keep clover/kexts/others/ minimal use only required kexts as per suggested by @Bronxteck (e.g. below kexts are required for this system ) FakeSMC.kext VoodooPS2Controller.kext SATA-100-series-unsupported.kext USBInjectAll.kext
  35. 2 points
    You forgot to mention it has discrete graphics as well. Your system is not Kabylake, not sure why you have MBP 15,2 as SMBIOS. So you have no graphics acceleration. Remove these from /S/L/E FakeSMC AppleIntelE1000 VoodooHDA realtechALC AppleHDA AppleIGB Replace the bootpack from here , goes into /EFI/Clover Also the SSDT-Disable-DGPU.aml goes into /EFI/Clover/ACPI/Patched Restore vanilla AppleHDA.kext from USB installer to /S/L/E You might need to add HFSPlus.efi into /EFI/Clover/drivers64UEFI Repair permissions and rebuild cache
  36. 2 points
    El Capitan Guide Specifications: Processor : Intel® Coreâ„¢ i7-5600U Processor (4M Cache, 2.60 GHz) Graphics Processor(GPU) : Intel® Integrated HD Graphics 5500 Chipset : Intel® 5th Generation Wildcat Point LP chipset Storage : Samsung PM851 256GB mSata-SSD RAM : 16GB DDR3L 1600 MHz DIMMS Wifi : Intel Wireless Gigabit Ethernet 802.11AC (M.2, 7265AC), Bluetooth 4.0 LE LAN : Intel I218-LM3 PCI-E Gigabit Ethernet Adapter Audio : Realtek® High Definition Audio ALC293 (ALC3235) USB 3.0 : Intel Wildcat Point-Lp - USB 3.0 xHCI Controller Touchpad : Alps Multi-touch Touchpad v8 Hardware Webcam : USB3.0 UVC HD WebCam Card reader : O2 Micro OZ777xxx/OZ62 PCI-E Card Reader Monitor : 35.5cm (14) FHD (1920x1080) Anti Glare (16:9) WLED, 300 nits, Magnesium LCD back Battery : 3Cells 40 Whr Lithium Polymer battery with ExpressCharge Interface : 1 x Microphone/Headphone Combo jack 1 x Mini DisplayPort for external monitor 3 x USB 3.0 port(s) 1 x RJ45 LAN Jack for LAN insert 1 x HDMI Working: Graphics with Acceleration Audio with patched AppleHDA Bluetooth /Wireless (Replaced with DW1560) HDMI Audio/Video mini Display Port LAN USB3.0 Webcam Battery Fn Hotkeys SD Card reader Alps Touchpad / Trackstick Sleep, Processor P&C-States with Native power management Not working: Finger Sensor, smart card reader if you have one Prerequisite: Set DVMT to 96MB (0x3) Source => FireWolf™s guide. Steps to change the DVMT value (Done on Windows or WinPE) 1) Universal BIOS Backup ToolKit 2.0.exe.zip - to backup the BIOS (DellInc.-A10.rom) At time of writing - BIOS version E7450A10 2) UEFITool.exe to find the module labeled SetupPrep and extract the PE32 image section (setup.bin) Update: For Dell Only: Search with this GUID then extracting the PE32 body under it would be faster /easier than finding the module per guide 899407d7-99fe-43d8-9a21-79ec328cac21 3) Universal IFR Extractor.exe to extract setup.bin to a readable text file 4) Use notepad to search for “DVMT†in the text file, 2 were found at 0x15b and 0x15c Both with value of 0x1 and need to be set to 0x3 5) Format a USB drive to fat32 and create a folder name EFI (SD Card works too) 6) Download the EFI Shell and extract the Boot folder to EFI folder i.e.. /EFI/Boot/bootx64.efi 7) Boot system with the USB and select UEFI Boot At the grub prompt, enter these commands, hit enter after each command, then exit and reboot setup_var 0x15b 0x3 setup_var 0x15c 0x3 To verify, just enter setup_var 0x15b and hit enter, the value will be listed Note: Settings retained even after BIOS update and no need to rerun again But will reset if you select Restore Settings in BIOS!!! /!\ New Development: If you don't want to mod the BIOS as it might be difficult for some models, you could skip this step by adding 2 new kexts to /EFI/Clover/kexts/Other Lilu.kext & Whatevergreen Installation: See here with Bootpack Post Install: Enable Brightness Control and Trackstick Scrolling Trackstick Scrolling Download and Install Karabiner Launch Karabiner/Preferences/Change key/Point Devices/CursorMove to ScrollWheel Enable MiddleClick+CursorMove to Scrollwheel Brightness Control Launch Karabiner/Preferences/Misc & Uninstall Under Custom Setting, click Open private.xml Replace file with the attached -> private.xml.zip Go back to Change Key Tab and select 'Reload XML' The new custom file will show on the very top call 'Remap Brightness Key' & 'Remap Volumes Key' Place the check marks there. Now Hit F11 & F12 for Brightness, hit F1, F2, & F3 for Volumes Control (Keyboards with same/similar layout will work with custom xml above too) Note1: Personally use SmartScroll for Trackstick scrolling with Inertia. Don't really use Touchpad, 2 fingers scrolling and tap and drag does work. Note2: Please use this beta version of ssdPRGen.sh for Broadwell system Credits: FireWolf, Joe82, EmlyDinEsh, Bronxteck, Hervé, Rehabman, Piker-Alpha, Sontrg, toleda, Dr. Hurt, Clover Team, ...anyone involved with getting Broadwell supported
  37. 2 points
    El Capitan Guide Specifications: Processor : Intel® Coreâ„¢ i5-6300U / i7-6600U Processor Graphics Processor(GPU) : Intel® Integrated HD Graphics 520 Chipset : 6th Generation Intel®Coreâ„¢ Storage : Samsung PM851 256GB M.2 Form factor Sata-SSD RAM : 16GB DDR4 SDRAM 2133 MHz; 2 slots supporting up to 16GB Wifi : Intel Wireless Gigabit Ethernet 802.11AC (M.2, 8260AC), Bluetooth 4.1 LAN : Intel I219-LM PCI-E Gigabit Ethernet Adapter Audio : Realtek® High Definition Audio ALC293 (ALC3235) USB 3.0 : Intel USB 3.0/3.1 xHCI Controller Touchpad : Alps Multi-touch Touchpad v7 Hardware Webcam : USB3.0 UVC HD WebCam Card reader : SD 4.0 Memory Card Reader Monitor : (14) FHD (1920x1080) Anti Glare (16:9) WLED, 300 nits, Magnesium Alloy LCD back Battery : 55 Wh ExpressCharge Capable (4-cell) Lithium-Ion Interface : 1 x Microphone/Headphone Combo jack 1 x Mini DisplayPort for external monitor 3 x USB 3.0 port(s) (one with PowerShare) 1 x RJ45 LAN Jack for LAN insert 1 x HDMI Working: Graphics with Acceleration Audio with patched AppleHDA Bluetooth /Wireless (Replaced with DW1560 / DW1830) HDMI Video / Audio mini DisplayPort / Audio LAN USB3.0 Webcam Battery Fn Hotkeys (Brightness & Audio control) Alps Touchpad / Trackstick Sleep, Processor P&C-States with Native power management Not working: Finder Sensor, smart card reader if you have one SD Card reader DisplayPort on Port Replicator - no DP audio Work in Progress: HDMI Audio (no support yet) HDMI Audio Supported, updated files in the Sierra guide below Slow to boot/Restart/Shutdown Better when dual booting with Win10/not sure why Prerequisite: Set DVMT to 96MB (0x3) Source = FireWolf™s guide Steps to change the DVMT value (Done on Windows or WinPE) 1) Universal BIOS Backup ToolKit 2.0.exe - to backup the BIOS (DellInc.-1.5.3.rom) At time of writing - BIOS version 1.5.3 2) UEFITool.exe to find the module labeled Setup and extract the PE32 image section (setup.bin) Update: For Dell Only: Search with this GUID then extracting the PE32 body under it would be faster /easier than finding the module per guide 899407d7-99fe-43d8-9a21-79ec328cac21 3) Universal IFR Extractor.exe to extract setup.bin to a readable text file 4) Use notepad to search for “DVMT†in the text file, 2 were found at 0x432 and 0x433 Both with value of 0x1 but only 0x432 needs to be set to 0x3 5) Format a USB drive to fat32 and create a folder name EFI (SD Card works too) 6) Download the EFI Shell and extract the Boot folder into the newly created EFI folder i.e.. /EFI/Boot/bootx64.efi 7) Boot system with the USB and select UEFI Boot At the grub prompt, enter these commands, hit enter after each command, then exit and reboot setup_var 0x432 0x3 To verify, just enter setup_var 0x432 and hit enter, the value will be listed Note: Settings will retain after BIOS update but will reset if you select "Restore Settings" in BIOS!!! /!\ New Development: If you don't want to mod the BIOS as it might be difficult for some models, you could skip this step by adding 2 new kexts to /EFI/Clover/kexts/Other Lilu.kext & Whatevergreen BIOS Settings: Set to "Load Default", Apply, then set the following: TPM = Disabled Secure Boot = Disabled UEFI = Enabled SATA Operation = AHCI Wake on Lan /WLan = Disabled Enable Legacy Option ROMs = Disabled Installation: See here install guide, use below bootpack E7x70.zip Note: Must be OS X 10.11.4 and newer for Skylake support Post Install: Enable Brightness Control and Trackstick Scrolling Trackstick Scrolling Download and Install Karabiner Launch Karabiner/Preferences/Change key/Point Devices/CursorMove to ScrollWheel Enable MiddleClick+CursorMove to Scrollwheel Brightness Control Launch Karabiner/Preferences/Misc & Uninstall Under Custom Setting, click Open private.xml Replace file with the attached -> private.xml.zip Go back to Change Key Tab and select 'Reload XML' The new custom file will show on the very top call 'Remap Brightness Key' & 'Remap Volumes Key' Place the check marks there. Now use F11 & F12 for Brightness, use F1, F2, & F3 for Volumes Control (Keyboards with same/similar layout will work with custom xml above too) Note1: Personally use SmartScroll for Trackstick scrolling with Inertia. Don't really use Touchpad, 2 fingers scrolling and tap and drag does work. Note2: Please use this beta version of ssdPRGen.sh generate SSDT.aml for Skylake system Note3: If you're installing Sierra, there's a known artifact issue on the upper left corner! Update: Fix can be found here Credits: FireWolf, Joe82, EmlyDinEsh, Bronxteck, Hervé, Rehabman, Piker-Alpha, Sontrg, toleda, Dr. Hurt, Clover Team, ...everyone involved with getting Skylake supported
  38. 2 points
    Try adding this to /EFI/Clover/kexts/Other
  39. 2 points
    Try this Config, I added the proper patches config.plist.zip
  40. 2 points
    Yes, replace with this one if it's not working Use layout-id 1
  41. 2 points
    To save your time, here's my kext. Put in /S/L/E, rebuild permission/cache or put inside IO80211Family.kext, whatever works. Also I attached the injector kext, put it in Clover/kexts/Other Remove the two obsolete kexts you use as well. AirPortAtheros40.kext.zip Ar9285Injector.kext.zip
  42. 2 points
    Ok, so it's a Haswell laptop with the following specs: Series 8 chipset i3-4005U @1.70GHz (no Turbo boost) 8GB RAM Intel HD 4400 graphics + Nvidia GeForce 820M 14.0" LCD 1366x768 Realtek RTL8106/RTL8111 Gigabit Ethernet DW1705 802.11n + BT4.0 wireless card (compatible but poorly supported; better to replace) Realtek ALC255 ? (ALC3223) audio USB 2.0 + USB3 ports HD Webcam Synaptics Touchpad If you have a SD card reader, it should be: Realtek RTS5170 Card Reader That laptop is perfectly able to run current macOS High Sierra and will support Mojave. Optimus technology being unsupported in Hackintoshes, you won't be able to have dual graphics, only the HD4400 (fully supported) or, possibly, the nVidia (if supported). We can look at extracting the ACPI tables (DSDT/SSDT) from your BIOS for eventual patching.
  43. 2 points
    Requirements Pendrive 2.0 (>=8GB) "Install macOS Sierra app" (https://itunes.apple.com/de/app/macos-sierra/id1127487414?l=en)(Around 5GB) Working Mac Installing Clover to USB Get a USB 2.0 Pendrive (8GB and above) Before you can partition the USB, you must determine what the disk identifier is. With the USB plugged in to the computer, use 'diskutil list': In Terminal: diskutil list In my case, output: /dev/disk0 (internal, physical): #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI EFI 209.7 MB disk0s1 2: Apple_CoreStorage MacOS 500.4 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s5 4: Microsoft Basic Data DATA 498.8 GB disk0s4 /dev/disk1 (external, physical): #: TYPE NAME SIZE IDENTIFIER 0: Pendrive *8.0 GB disk1 As you can see my pendrive is available at /dev/disk1 (check yours). Now we are going to create partitions, In Terminal: diskutil partitionDisk /dev/disk1 1 GPT HFS+J "install_macos" R Output: Started partitioning on disk1 Unmounting disk Creating the partition map Waiting for the disks to reappear Formatting disk1s2 as Mac OS Extended (Journaled) with name install_osx Initialized /dev/rdisk1s2 as a 7 GB case-insensitive HFS Plus volume with a 8192k journal Mounting disk Finished partitioning on disk1 /dev/disk1 (external, physical): #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *8.0 GB disk1 1: EFI EFI 209.7 MB disk1s1 2: Apple_HFS install_macos 7.7 GB disk1s2 Now as you can see partitions are created and your pendrive is ready to install clover. Download the Clover installer. Current builds are available on sourceforge: http://sourceforge.net/projects/cloverefiboot After Downloading the Clover installer, Install it to the Target "install_macos" partition using "Change Install Location". Select "Customize". Check "Install for UEFI booting only", "Install Clover in the ESP" will automatically selected. Check "BGM" from Themes. Check "AptioMemoryFix.efi", "EmuVariableUefi-64.efi", "OsxFatBinaryDrv-64.efi" from Drivers64UEFI. After making your selections, Click "Install". Finally, one more EFI driver is needed, HFSPlus.efi: Download from : https://github.com/JrCs/CloverGrowerPro/raw/master/Files/HFSPlus/X64/HFSPlus.efi. Copy to /EFI/Clover/drivers64UEFI. Kext Setup Remove all folders from EFI/CLOVER/kexts/ except 'Other'. Now Download These, FakeSMC.kext: https://github.com/RehabMan/OS-X-FakeSMC-kozlek VoodooPS2Controller.kext: https://github.com/RehabMan/OS-X-Voodoo-PS2-Controller USBInjectAll.kext: https://github.com/RehabMan/OS-X-USB-Inject-All Lilu.kext: https://github.com/vit9696/Lilu IntelGraphicsFixup.kext: https://github.com/lvs1974/IntelGraphicsFixup RealtekRTL8100.kext: https://www.insanelymac.com/forum/files/file/259-realtekrtl8100-binary/ Setting config.plist Download it from the attachments, Unzip and replace EFI/CLOVER/config.plist Building the MacOS Installer In Terminal : sudo "/Applications/Install macOS Sierra.app/Contents/Resources/createinstallmedia" --volume /Volumes/install_macos --applicationpath "/Applications/Install macOS Sierra.app" --nointeraction sudo diskutil rename "Install macOS Sierra" install_macos Now your Bootable USB is ready to install. Turn off your Laptop. Installing Make sure you have adequate bios settings Then Follow: Power on laptop with pendrive connected to it. Continuously press "ESC". Select "Boot From USB" (i.e. F9) and select pendrive from the menu. Now it boots into Clover, with left-right arrow, select options. Select "Graphics Injector Menu". Under "Inject Intel" select "FakeID" and replace "0x00000000" to "0x12345678". Now return to main screen and select "install_macos". When grey screen comes, select DiskUtility. Format whole Hard Disk as "Mac Os Extended (Journaled)" with Name as "MacOS" Now quit DiskUtility and click "Install Mac OS Sierra" and select the newly created partition in previous step. Now installer will begin installing files (~15-20mins) and the restart. After restart again boot into clover(Follow Step 1-5) and again select "install_macos". Now Install screen will appear and continue installation. This time installer will install files to your target partition and create Recovery HD partition. Later on restarts. After restart again boot into clover(Follow Step 1-5) and again select "MacOS". If everything goes well, you will finish up the installation process and arrive at the Mac OS Sierra desktop. Install clover to hdd. Congratulations!! Your Installation is complete!! Now you need to fix things one by one. Will Provide fixes when I get time.
  44. 2 points
    I am glad you enjoy it.
  45. 2 points
  46. 2 points
    if you emulate an smbios of a APPLE machine that uses soldered on ram then it will not have the memory tab.
  47. 2 points
  48. 2 points
    @vinh1978, whenever you try something new suggested by some member and yet are unable to fix the problem then when you report back (after trying) you are expected to provide new problem reporting files (it is written clearly in FAQ thread for gen_debug). Why submit new files everytime you try changing something? Coz, if you change the files many other things also change and they help keep track of how close we are from fixing the problem. Without new files after change, it is like shooting in the darkness and hoping to hit the bull's eye. Hope you understand. Regards
  49. 2 points
    High Sierra High Sierra Guide Bootpacks E7470_1.17.5_HS.zip E7470_1.17.5_HS-alternate.zip E7270_1.17.5_HS.zip E7270_1.19.4_HS.zip Note: 1) Copy kexts in /EFI/Clover/kexts/Other/CopyToLE to /Library/Extensions. Repair permissions and rebuild cache 2) Enable this patch in Config.plist under KextsToPatch if you have: LiteOn, Plextor, or Hynix NVMe Hynix NVMe patch 10.13.x (Bit swap block size 0x10) -Syscl UPDATES High Sierra 10.13.1 (17B48) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Install latest Clover prior to update High Sierra 10.13.2 (17C88) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Install latest Clover prior to update Install latest Lilu.kext v1.2.1 High Sierra 10.13.3 (17D47) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Install latest Clover prior to update Install latest Lilu.kext v1.2.1 High Sierra 10.13.4 (17E199) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Install latest Clover prior to update Install latest Lilu.kext v1.2.1 High Sierra 10.13.5 (17F77) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Install latest Clover prior to update Install latest Lilu.kext v1.2.3 High Sierra 10.13.6 (17G65) STATUS: GOOD UPDATE METHOD: APP STORE/SYSTEM UPDATE MODIFICATIONS NEEDED: Update USB port limit patch
  50. 2 points
    Sierra Guide See here for install guide, just replace with Sierra bootpack. E7x70_Sierra.zip - See Update files below Known Issue & Workaround: HDMI-Output works but if connect HDMI-Cable the local Display goes off and never recovers. I had tried different configurations but none panned out. Here's a workaround: Close the LID until you see the HDMI display becomes the primary display, then open the LID. It'll switch LCD as primary and HDMI as secondary. NOTE: Workaround is only needed on clean boot, no issue if system has gone through a sleep/wake cycle Post Install: Enable Brightness Control and Trackstick Scrolling Trackstick Scrolling Download and install Smartscroll for trackstick scrolling Touchpad - 2 fingers scrolling, 2 finger tab for right click, tap and drag Brightness Control Download and Install Karabiner-Elements Launch Karabiner-Elements Copy karabiner.json to ~/.config/Karabiner karabiner.json.zip or copy the settings according to diagram below Now use F11 & F12 for Brightness, use F1, F2, & F3 for Volumes Control
This leaderboard is set to Amsterdam/GMT+02:00
×
×
  • Create New...