Jump to content

tonykai

Members
  • Posts

    20
  • Joined

  • Last visited

Posts posted by tonykai

  1. Hello , 

     

    I was complete installed MacOs Catalina on my laptop by use Olarila.catalina.101.15.4 image (https://www.olarila.com/) on this week .

    Then add some patches via use HackIntool_v3.4.0 to add Coffee Lake Framebuffer patches.

    Now UHD 630 can work .

     

    But there are still exist two problem on my laptop .

    1, Trackpad can't work .  i don't know that if it is a common problem .

    2, can't adjust screen brightness.

     

    Please help me and give some suggestions .

    Thank you

    Attachment is my config.plist and kexts photo.

     

     

     

     

    Dell5491_UHD630.jpg

    Kexts.jpg

    config.plist.zip

  2. hello, below is detail hardware configure for my laptop dell 5491:

    Bios: 1.11.1

    CPU: Coffee Lake i5-8300H @2.3G

    Graphics: Coffee Lake UHD630

    Memory: 8GB DDR4 2666MHz

    Mainboard: DELL 0NFNN4 (CM246 Chipsets)

    SSD: TOSHIBA 256G NVMe (primary)

    HDD: SATA ST1000LM049  1T (second)

    Sound: Realtek ALC256 

    LAN: Intel I219LM7

    Wireless/Bluetooth: Qualcomm QCA61X4A 802.11AC Wireless Adapter

     

    I try to install from clover in verbs mode .

    I found out that screen will stuck at apfs_module_start:1689 

     

    Thanks for every information you can give to me .

    Attachment is error photo and EFI file .

    error_apfs _module_start_1689.jpg

    config.plist.zip

  3. Hello, below is detail hardware configure for my laptop 5491:

    • Bios: 1.11.1
    • CPU: i5-8300H @2.3G
    • Memory: 8GB DDR4 2666MHz
    • Mainboard: DELL 0NFNN4 (CM246 Chipsets)
    • SSD: TOSHIBA 256G NVMe (primary)
    • HDD: SATA ST1000LM049  1T (second)
    • Sound: Realtek ALC256 
    • LAN: Intel I219LM7
    • Wireless/Bluetooth: Qualcomm QCA61X4A 802.11AC Wireless Adapter

     

    I had been completely install Mojave 10.14.6 on my laptop DELL 5491. Then I find out these problems:

    1. UHD Graphics 630 was only showed 7M
    2. Sound card (Realtek ALC256) cannot work, I try inject ID 5/11/13 /21/22/28/56 But it cannot still work
    3. Touchpad cannot work
    4. Qualcomm QCA61X4A 802.11ac Wireless card cannot work

     

    Please help me and give some suggestions to solve it.

    Attachment is my config.plist

     

    UHD630_onlyShowned_7M.jpg

     

    kexts_files.jpg

     

    HdaCode_files_music.jpg

     

    config.zip

     

  4. Dear Jake Lo ,

     

    According your suggestion,  i enter clover system via USB disk , then go into MacOs ,

    then Mount the EFI partition of the Installed drive in local disk ,

    then delete config.plist file and delete all files and including folders which is belong to  under \EFI\CLover\ACPI folder .

    then copy config.plist file and all files under ACPI which come from E7450_A20_tonykai.zip .

    then reboot MacOS and remove USB disk .

    Finally , i can't still go into MacOS . 

    Below is error information pic .

    i attached current the whole EFI folder which is modified according E7450_A20_tonykai.zip .

     

    you can download this current whole EFI folder file ( CLOVER_20190415.zip).

    https://mega.nz/#!6BFgCK5T!hG9oLjmm1s6Kl2It3ssn5wzdRG_VhEq0qiZoRp9mMeI

     

     

    BR

    Kai

    IMG_20190415_031823.jpg

  5. Dear Jake Lo ,

     

    According your suggestion,  i enter clover system via USB disk with my_original EFI boot system , then enter MacOs after  press F4 , 

    I attached Origin.zip which is belong to the whole  /EFI/Clover/ACPI/Origin folder.

     

    I have one question need your help . When you give patch the files to me , How are i use it ?

    if i need do below these actions , isn't it ?

    1, remove all files which is belong to under EFI folder .

    2,   copy the whole EFI folder which come from USB Disk into Local disk .

    3,use  Exx50_Mojave.zip to replace EFI files base on current files under EFI folder 

    4,    copy patch files which come from you into /EFI/CLOVER/ACPI/patched folder 

     

    Thanks 

    Kai

    origin.zip

  6. Dear Jake Lo ,

    According your suggestion, i enter winpe system in my laptop E7450 ,

    then use Universal BIOS Backup ToolKit 2.0.exe tools to backup the BIOS (DellInc.-A20.rom) ,

     

    then use UEFITool.exe to find the module labeled SetupPrep and extract the PE32 image section .

    I am  search with this GUID then extracting the PE32 body under it would be faster /easier than finding the module per guide

              899407d7-99fe-43d8-9a21-79ec328cac21

     

    then use Universal IFR Extractor.exe to extract setup.bin to a readable text file (Section_PE32_image_Setup_SetupPrep_body IFR.txt)

     

    then i use Use notepad to search for "DVMT" in the text file, 2 were found at 0x15b and 0x15c

    then i format a new USB drive to fat32 and create a folder name EFI and extract ( EFI Shell) the Boot folder to EFI folder ,for example: i.e.. /EFI/Boot/bootx64.efi.

    then i reboot laptop via this new USB Boot system and i can successfully enter command windows .

    then i  enter below these commands, hit enter after each command.

    setup_var 0x15b 0x3

    setup_var 0x15c 0x3

     

    finally ,i exit command windows and reboot laptop and remove USB disk , but i can't still enter MacOS via efi boot system which in local disk (use Exx50_Mojave.zip to replace EFI files base on  my original EFI boot file )   , system will still show error information "  busy timeout  IGPU  " .

     

    BR

    Kai

     

     

    error_1.jpg

    IMG_20190414_102518.jpg

    IMG_20190414_105639.jpg

    Section_PE32_image_Setup_SetupPrep_body IFR.zip

  7. Dear Jake Lo ,

     

    I will explain my mean.

     

    Frist  Whether use local disk or USB disk ,i can all enter MacOS via  my original EFI boot file , but Graphics HD5500 is showed 7MB.

     

    below download link address is original EFI boot file . -- original_CLOVER.ZIP

    https://mega.nz/#!CQczWQCL!du7F4CiK-vy-O-mtt09uoj1FQuWgXLH8IDtJ4ZqN-iY

     

    then  i use  Exx50_Mojave.zip to replace EFI files base on  my original EFI boot file in local disk . 

    finally i find out i can't enter MacOS  , system always show error information " busy timeout  IGPU ", then i enter Clover option menu ,then  select Graphics Injector interface -> select InjectIntel and change value to 0x12345678 for FakeID , i still can't enter MacOS .

    below download link address is the last EFI boot file ( use  Exx50_Mojave.zip to replace EFI files base on  my original EFI boot file ) -- CLOVER.ZIP

    https://mega.nz/#!SNEEAQBD!Mqp5niflQIUTAZ-wSX_3scgZv7cTBZKFPNc0jUMhhrQ

     

    So current i only enter MacOS via use USB disk and use  my original EFI boot file .

     

    BR

    Kai

     

  8. Dear Dear Jake Lo ,

    usb flash disk boot is use my original EFI boot file which haven't use Exx50_Mojave files to replace .but Graphics HD5500 is showed 7MB.

     

    Beacuse i all can't enter Mac OS via EFI boot files ( use use Exx50_Mojave folder files to replace my original EFI files )  which is in local disk  or enter Clover option menu ,then  select Graphics Injector interface -> select InjectIntel and change value to 0x12345678 for FakeID .

     

    BR

    Kai

     

     

     

  9. Dear Jake Lo ,

     

    According your suggestion, I  enter MacOS via usb flash disk boot . then copy these two kexts (lilu.kext and Whatevergreen.kext ) into /EFI/Clover/kexts/Other folder.then run two commands "  sudo touch /System/Library/Extensions && sudo kextcache -u /" and "sudo touch /Library/Extensions && sudo kextcache -u /" under terminal windows for refresh cache .

     

    finally , i reboot my loptop and remove usb flash disk , but System will still show error information to me for busy timeout(0) 60s :IGPU .

    below is error information picture .

     

    by the way ,

    I attached the last clover.zip file which is after  replace original files under current EFI folder via use Exx50_Mojave folder give you for reference.

    You can download clover.zip via click the below link.

    https://mega.nz/#!SNEEAQBD!Mqp5niflQIUTAZ-wSX_3scgZv7cTBZKFPNc0jUMhhrQ

     

    If you would like remote my this laptop to survey this trouble via termviewer ? 

     

    Current i can't enter MacOS via use Exx50_Mojave.zip boot file , but i can enter MacOS via usb flash disk.

     

     

    Appreciate your reply .

     

    BR

    Kai

     

    IMG_20190414_011630.jpg

  10. Dear Jake Lo ,

     

    According your suggestion ,

    At frist i set my laptop BIOS to Load Defaults and apply it , then set the BIOS to UEFI/AHCI/Legacy Option ROMs enable and Secure boot Disabled , create a new Boot Options for MacOS.

     

    then i completed update MacOs Mojave from 10.14.1 to 10.14.4 after use my original EFI files enter MacOS.

    then update Clover boot system from v4862 to v4910 .(Note : if i select PartitionDxe-64 option in process of install clover_v2.4k_r4910.pkg ,  Clover install will be fail .)

     

    then i reboot MacOS  , I completed to redownload Exx50_Mojave.zip file and unzip it .

    then i use these files which is under Exx50_Mojave folder to replace original files under current EFI folder and copy this three files (BrcmFirmwareRepo.kext ,BrcmPatchRam2.kext,DisableTurboBoostBattery.kext ) to \library\extensions\ . then  use Kext Utility to refresh cache .

     

    Finally ,i reboot MacOS , System will still show error information to me for busy timeout(0) 60s :IGPU .

     

    Then i reboot laptop ,then enter Clover option menu ,then select Graphics Injector interface -> select InjectIntel and change value to 0x12345678 for FakeID , then click return to the main menu ,then boot macOS , finally , system is still show error information .

     

    I attached some pictures and clover.zip which is after  replace original files under current EFI folder via use Exx50_Mojave folder give you for reference.

     

    You can download clover.zip via click the below link.

    https://mega.nz/#!DMUh1CbY!ATgbn7zdOSn-YcPs2ZqXSVfBTi-0licifkZLxdlUWE8

     

    BR

    Kai

     

    IMG_20190413_110807.jpg

    IMG_20190413_100954.jpg

    HD5500.jpg

    IMG_20190413_110644.jpg

    IMG_20190413_110854.jpg

  11. Dear Jake Lo,

     

    I had been  complete modify dvmt value according your post .(  setup_var 0x15b 0x3   and  setup_var 0x15c 0x3)

    then i re-install macOS Mojave 14.3, then paste files from Exx50_Mojave.zip into CLOVER folder .

    finally , the same problem is still exist for show busy timeout  'IGPU' in boot process.

    i try press O to get to Options under  Clover gui,then enable Graphics Injector and Select platform-id and change it to 0x12345678,  the same problem is still exist.

     

    So please help me give a whole ‘EFI’ folder files .

    BR

    Kai

  12. Dear Jake Lo ,

     

    According your suggestion , I select FakeID and change value to 0x12345678 under clover interface for Graphics option   ,then click return to the main menu ,then boot macOS , finally , system code is always stayed for 'IOConsoleUsers:gIOScreenLockState 3 bs 0,now 0, sm 0x0 ' . I waited 10 minutes , system can't still go to MacOS login interface. select  platform-id   and change value to 0x12345678, The issue is same .

     

    By the way , for epair permissions and rebuild cache , if i can use Kext Utility app to do it ?

     

    Attached files are error info pic and current my laptop configration info under Bios .

     

    IMG_20190118_134555_2.jpg

     

    Bios_E7450_1.jpg

     

    Bios_E7450_2.jpg

     

    BR

    Kai

     

  13. Dear JakE Lo,

     

    According your suggestion , i delete config.list file and the whole folders for ACPI and kexts under Clover folder, then copy these file and folders which come from Exx50_Mojave.zip , and copy these three files (BrcomFirmwareRepo.kext ,BrcomPatchRAM2.kext,DisableTurboBoostBattery.kext) to S/L/E folder , finally i reboot laptop .

     

    Now system is always show 'Busy  Timeout  60s IGPU', and i waited 10 minutes,it still can't go to Mojave system .IMG_20190117_154733.thumb.jpg.9c94cf5102f2b32987ffc7f24f80f8c7.jpg

     

    Attached is error pic .

     

    BR

    Kai

     

     

  14. Dear eC//FrEak ,

    According your provide mothed , i adjust these kext files which files under Other folder and  move FakePCIID.kext & BrcmPatchRAM2.kext this two files  into S/L/E folder, and To enable "AppleIntelCPUPM" in my "config.plist" and change it from "false" to "true" . 

     

    then i reboot macOS , system is still show error info for 'IGPU Graphics driver failed to load ', i attached error pic .

    for ' use bootarg "alcid=layout-id" this step : i don't know that where can i to do it , if i do it in 'config.plist' ,isn't it ?.

     

    By the way ,

     

    i try use new files for config.plist  file and Kexts folder and acpi folder which come from Exx50_Mojave ( mothed which come from @Jake Lo ), but issue is still exist .

    IMG_20190117_011209.thumb.jpg.8df7a3db08204199c68f99224f177297.jpg

     

    BR

    Kai

  15. Hello guys:

    Blow is my laptop configuration :

    Type: Dell Latitude E7450 (Clover) Intel Broadwell-U -5th Generation Dell 0HPRCX
    CPU: [email protected]
    Graphics: Intel HD5500 (128M under win10, 64M under Bios), 1920x1080P
    RAMDR3L 1600 16GB
    SSD:256G
    Audio: Realtek @intel High Definition Audio Controller
    network: Inter Ethernet connection 1218-LM 
    wirlessell :Wireless 1560 802.11ac
    Bluetooth:W1560 Bluetooth 4.0 LE
    Bios: A20 version (UEFI boot)

     

     I've recently installed Mojave 10.14.2 on my E7450, but I'm having a few problems need your help .

     

    1, IGPU Graphics driver  failed to load  and HD 5500 Graphics RAM size is only showed 7M under MacOS Mojave

        i attached error pic 

     

    2,When click 'sleeping' button under Mojave system tools , system haven't anything response.

     

    by the way:

    There are blow these files under Kexts folder :

    AirportBrcmFixup.kext

    AppleHDADisabler.kext

    ApplePS2SmartTouchPad.kext

    BrcmFirmwareData.kext

    BrcmPatchRAM2.kext

    FakePCIID.kext

    FakePCIID_Broadcom_WiFi.kext

    FakeSMC.kext

    IntelMausiEthernet.kext

    Lilu.kext

    NullCPUPowerManagement.kext

    IntelGraphicsDVMTFixup.kext

    USBInjectAll.kext

    VoodooHDA.kext

    VoodooPS2Controller.kext

    WhateverGreen.kext

     

    Thanks

    BR

    Kai

     

     

     

     

     

     

    config.zip

    IMG_20190116_134539.jpg

×
×
  • Create New...