vclawson

Hey Jake, No this is not working. This is what my system info shows. Still has Country Code: XT en1: Card Type: AirPort Extreme (0x14E4, 0x2123) Firmware Version: Broadcom BCM43xx 1.0 (7.15.166.24.3) MAC Address: 00:6b:9e:06:13:ed Locale: Unknown Country Code: XT Supported PHY Modes: 802.11 a/b/g/n/ac Supported Channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 Wake On Wireless: Supported AirDrop: Supported Status: Not Associated

Hello Jake, Any idea what I could be missing? I have tried everything I can think of.

ok I'll look him up. What do you think I'm missing for the 5GHz?

Still the same. Also as far as the sleep thing. Is there a way to use the HD4000 only and still be able to use the HDMI out for an external monitor? I tried using the skipNvidiagfx and turning on and off optimus but could not find one that would allow it. If I do that will sleep work?

Jake, I think we are getting somewhere but we are not quite there. I installed the fakeSMC and now I have the following in the system info: Card Type: AirPort Extreme (0x14E4, 0x2123) Firmware Version: Broadcom BCM43xx 1.0 (7.15.166.24.3) MAC Address: 00:6b:9e:06:13:ed Locale: Unknown Country Code: XT Supported PHY Modes: 802.11 a/b/g/n/ac Supported Channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 Wake On Wireless: Supported AirDrop: Supported Status: Not Associated Still no higher channels and the country Code I think needs to be US.

Jake, I ran those commands and rebooted but see no change. I still can't see any 5GHz networks and the System Info still is not showing the 5GHz channels.

Thanks Jake. I guess my problem is I'm not sure how to do that patch. What do I use to replace those numbers and in what file?

I just finished installing Yosemite 10.10.3 on my E6430 and everything is working great except for two issues. My specs E6430 Core i5 NVS5200/HD4000 Optimus disabled in bios 8GB RAM WiFi card is AzureWave Broadcom BCM94352HMB I followed this guide to get the WiFi and bluetooth working http://www.tonycrapx86.com/network/104850-guide-airport-pcie-half-mini-v2-89.html I'm using the latest chameleon boot loader My two issues are as follows: 1. I can't recover from sleep - I have to hard reboot if it goes to sleep. 2. I can only see 2.4 GHz wifi networks. I cannot see any 5GHz networks. I have tried the kexts on the above site to no avail. Any help would be appreciated.

Thanks for the response. How do I go about finding out why the External Monitor won't come on through VGA?

Graphics are working great at the moment except that I can't get the external display to come on. Do I need a separate kext for the 2007WFP?

I got it to install finally. Thanks for the help. I was actually using the USB 3 ports on the right hand side and tried using the USB 2 on the left and it worked. At first it would only boot up in safemode but I downloaded Jake Lo's extra folder and now it boots up fine everytime.

Ok, a little progress. I erased my USB and created a new OSX installer and installed the Extra Folder. Ran the myFix and tried again. It now will get to the bootloader and I put in -v. It loads all of the kexts and then looks like it is starting up. Then it freezes. No indication of a kernal panic. The last lines indicate it is working on the AppleIntelCPUPowerManagement. Says initialization complete. Says AppleSmartBattery Manager Loading... three times then AppleSmartBattery Loading... once. That is where is freezes. Picture attached. oops, two of them attached.

I get it when booting from USB. I have had this before and was able to reinstall chameleon from myhack and it worked but not this time.

Thanks, I tried that thread and put in the Extra folder from it from Jake Lo. The USB install kept coming up with boot0: error even after trying to reinstall chameleon. Then I when to Jake Lo's thread on it and used the Extra folder from that one. Again got the same boot0: error. Not sure what I am doing wrong.

I have gone through the thread of installing on E6400 in 5 easy steps but can't seem to get mountain lion to install. first of I I have an E6430 with 8GB RAM. Nvidia NVS 5200. I created the USB drive using myhack and a 10.8.3 InstallESD.dmg. I used the Extra folder for the thread mentioned above. The first time I try to install it gives me the boot0: error. So I used myhack and reinstalled chameleon. It gets through after that and I type in -v and start the install. It then gives a kernal panic saying that there should be 4 threads but only found five. I found online that this is due to the DDST.aml file. So I renamed it and started the install again. Now I get a kernal panic and says that the extension in the backtrace is com.apple.driver.AppleIntelCPUPowerManagement. Is it a problem that I am using 10.8.3 to try this install? Should I use 10.8.2 and then try to upgrade? Any help would be appreciated.