jackbaurctu Posted July 15, 2019 Share Posted July 15, 2019 Hi i have e7270 and during boot to install, im stuck at ramdomseed see pictures can anyone help me to get the install working thanks in advance Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted July 15, 2019 Moderators Share Posted July 15, 2019 Replace this into /EFI/Clover and try again. Set BIOS with the following settings: Set to "Load Default", Apply, then set the following: TPM = Disabled Secure Boot = Disabled UEFI = Enabled SATA Operation = AHCI Wake on Lan /WLan = Disabled Enable Legacy Option ROMs = Disabled Don't use Clover 4988, I have the same boot failure. Use and older version. Link to comment Share on other sites More sharing options...
jackbaurctu Posted July 16, 2019 Author Share Posted July 16, 2019 thanks for the reply I tried with 4972 and 4920 im stuck at randomseed same as before I also tried with your bootpack and replace /EFI/Clover but whenever I boot with USB I see nothing in clover Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted July 16, 2019 Moderators Share Posted July 16, 2019 You're probably missing HFSPlus.efi Make sure to replace the files into /EFI/Clover, not replace Clover with the bootpack Install clover with the following settings Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\DataHubDxe-64 Drivers64UEFI\FSInject-64 Drivers64UEFI\SMCHelper-64 Drivers64UEFI\ApfsDriverLoader-64 Drivers64UEFI\AptioMemoryFix-64 Drivers64UEFI\PartitionDxe-64 Add to Drivers64UEFI\HFSPlus.efi (Not included in Clover installer) Link to comment Share on other sites More sharing options...
jackbaurctu Posted July 16, 2019 Author Share Posted July 16, 2019 thanks a lot you were right after adding HFSPlus.efi i was able to boot much further but now Im stuck at IOConsoleUsers: gIOScreenLockState 3, hs 0,bs 0, now 0, sm 0x0 Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted July 16, 2019 Moderators Share Posted July 16, 2019 add the following boot arg until you finish installing. Basically it needs the Graphics kext to be cached before the patches from the Config file will work. I think I have stated this a few posts above for another member. At Clover, press "O" to get to Options. Append this to the end of the boot arg -igfxvesa Link to comment Share on other sites More sharing options...
jackbaurctu Posted July 16, 2019 Author Share Posted July 16, 2019 Thanks -igfxvesa works I managed to format APFS install macos it rebooted 2 times but now Im stuck at this Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted July 16, 2019 Moderators Share Posted July 16, 2019 are you still booting with -igfxvesa? 1 Link to comment Share on other sites More sharing options...
jackbaurctu Posted July 16, 2019 Author Share Posted July 16, 2019 Yes I did I tried with and without -igfxvesa hangs same place Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted July 16, 2019 Moderators Share Posted July 16, 2019 Can't really tell since the error occurred way before that last line. Try this, go to Option during Clover boot. Go down to graphics injector and change ig-platform-id to 0x12345678 and faked to 0x12345678 see if you could boot from that 1 Link to comment Share on other sites More sharing options...
Recommended Posts