Beta1382643440

Can you link us to the support page for your MB. Also this is not DSDT related.

In the DSDT change the device ID to on that is supported for ICH10.

What DSDT edit have you been using for HD4000 Can you post it.

The ENABLE IF NO EXT PEG means that the Onboard VGA (GRAPHICS) would be activated (enabled) if there is no dedicated video card detected ( like your GT 220) BUT if the dedicated GPU was detected then the Onboard graphics would be deactivated. No. If it is always on if you do not turn it off. Did you trun it off? Also there is nothing wrong with the motherboard,

Under Advance BIOS Features: Onboard VGA Enables or disables the onboard graphics function. Auto Allows you to set up a dual-display configuration in Windows 7 operating system. (Default) Enable If No Ext PEG Activates the onboard graphics only when no PCI Express graphics card is installed. Always Enable Always activates the onboard graphics, whether or not a PCI Express graphics card is installed. If you wish to set up a dual-display configuration, set this item to Always Enable. You just needed to take it slower and look at all the menus.

-v npci=0x2000 GraphicsEnabler=No It is stuck on the intel graphics. Disable it in the BIOS and boot again.

Boot with: -v npci=0x2000 GraphicsEnabler=No Then post a new pic were it hangs.

Done DSDT.aml.zip

With out a IOreg the DSDT is useless. :/ Please post a IOreg.

Again you are not following what I had asked you to do. You booted with: –x –f –v npci=0x3000 GraphicsEnabler=No Please boot as instructed and you have NO IDEA what you are doing in regards to boot flags so please do not experiment. With what you booted with it will never work. If you want help DO AS TOLD.

Please post in a well organized mater so that people can follow what your specs are and what you have done. Second I can tell you have no understanding in regards to what the boot flags do so please review the following before continuing: http://forum.voodooprojects.org/index.php?topic=351.0 There is a non fixable with this system: GA-B75M-D3P Intel I3 2120 HD2000 (Unsupported So Do Not Bother) Looking at: Gigabyte z68ap-d3 Intel Pentium G630 Asus Nvidia 210 Boot with myHack with the following flags: -v GraphicsEnabler=No Post a pic were it hangs showing the full screen. Also make sure you are not connected to a USB 3.0 port and are using a USB 2.0 port on the back of the system.

Very simple to do. Follow my guide here: http://rampagedev.wordpress.com/guides/ ... to-a-dsdt/ This is the DSDT injection code for your card and for HDMI audio as well.

Ok, so just install that kext I told you to and you will be fine.

This has NOTHING to do with the boot loader. For example you have 4 flat tiers and you think that putting gas in the car will fix the issue....

You need to install NullCPUpowermanagment.kext

Proper fix for Ethernet Built In without using a boot flag is DSDT injection. See my guide here: http://rampagedev.wordpress.com/2012/07 ... to-a-dsdt/

I support all x79 systems vis my blog: http://rampagedev.wordpress.com/2012/07 ... dati-gpus/

-v GraphicsEnabler=No

You will need to install the USB roll back drivers in your extra folder from 10.6.2 and 10.6.4 to install on that chipset.

Do you have a blue tooth dongle?

It has nothing to do with the bootloader. Use the one that myHack installs on the USB drive. POST A PIC AS REQUESTED WERE IT HANGS!

Boot with the following and then post a picture of were it hangs: -v GraphicsEnabler=No

Do you have protools? And do you have recording equipment attached?

Boot with: -x debug=0x144 This will remove the shutdown notice so I can see the whole screen.

Install the kexts in my AsRock DMG and the Extra folder as well while I work on your DSDT. You are only useing one core right now. Once you do as I say you will be able to boot on your own.