Beta1382643440

Ok, I applied a few more edits including ethernet Built in fix so you no longer need that switch in your boot.plist. Also I fixed a few device ID's that are more appropriate to motherboard chipset. Last your power button will now work with this DSDT. Post another IOreg as you did before. DSDT.aml.zip

No that is wrong your values are: 21 2100 Remake your SSDT and then post it here and I will check it.

Create a SSDT. Follow my guide here: http://rampagedev.wordpress.com/category/ssdt/

Yes, I have it installed. There are no major changes other then new wifi drivers.

Here is a edited DSDT. I did not have to do much since your DSDT was very clean and tidy to start with. DSDT.aml.zip

Added some PCI information so it displays correctly under system profiler and added ethernet built in fix so you can remove that fix from the boot.plist DSDT.aml.zip

Another solution would be to inject your ATI card into your DSDT and then place your DSDT in your Extra folder of the installer. Worked for me.

Download MB and install just the networking kexts form it to get lan working. For wireless do some research and see what other models work in your laptop. Install the network drive then restart and make a new IOreg then compress your entire extra folder and then I will continue editing.

Here is the last edited DSDT. Not much else I can do until you get built in Lan and Wireless card. DSDT.aml.zip

Yes, I am using a external flash drive. I thought I was using the appropriate boot flags and from your response I was. I will follow your recommendation.

IOreg is corrupt. Please make a new one and repost it.

Now for the real editing to begin! I need you to post your IOreg from your system so I can complete the DSDT. Use my guide here: http://rampagedev.wordpress.com/2012/07 ... use-ioreg/ Then post your IOreg here.

I have been working on this for a week and I am still stuck on why I can not get it to work. Ideas? Used: -v -x cpus=1 USBBusFix=Yes System Specs: http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=5119235#N816

Test this DSDT report back if you are able to post with it then we can go from there. DSDT.aml.zip

You need to use the USB installer drive to boot into your system. Then you will need to install the appropriate kexts for your system to boot properly on its own.

My install guide for ML using myHack: http://rampagedev.wordpress.com/os-x-10-8-mountain-lion/

Boot with the following: "Graphic Enabler"=No Then you will get to the desktop. I would recommend to get around this issue to inject your GPU into your DSDT.

Here is a edited and patch dsdt. Please run IOreg that is in the folder and then post that file. Files.zip If you can not boot with the DSDT boot with the following boot flag: DSDT=No Note this is case sensitive What audio solution are you using because I added HDEF to the dsdt and this will conflict with any voodoo kext.

I have a Asus Rampage IV Extreme x79 motherboard and when I try to boot using the hard drive it hangs at the storage kext. However when I load from the USB drive it does not and boots right away. I also installed an asmedia kext for the asmedia controler. Could this be the issue?

Ok, where in the DSDT do I put it. Where I put it it did not load the frame buffer. Showed up as 6xxx.

Great. I have a MSI R6870 Hawk Radeon now and a ATI 5770. I need to update my specs.

How to add GPU into DSDT to get rid of graphics enabler=yes At this point on my oldest mac build I am almost done. In my plist I only have kernel cache, quiet boot, and graphics enabler=yes. I was wondering if you could add the framebuffer some how so that graphics enabler=yes is not needed. Thanks.

If you can post you DSDT at a file sharing site I can look at it for you.

I found out that the BIOS of the MB was the issue. Now that I am past that the DSDT I am working is causing a few issues when I start appling patches other then the ones to clean up the errors. Also I can not find very much information on how to get the x79 chipset to be read properly under system profiler or the ALC898 audio.

Asus Rampage IV Extreme LGA 2011 I installed Lion using Myhack and can use the installation if I boot from my usb drive and it runs great. However the bios does not see the HD as bootable after installing lion. Ideas?