Jump to content

Chris261

Members
  • Posts

    2
  • Joined

  • Last visited

1 Follower

Profile Information

  • Gender
    Male
  • Location
    Melbourne, Australia

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Chris261's Achievements

Private

Private (2/17)

1

Reputation

  1. Hi Everyone, I thought I would post details of my successful High Sierra build. Thanks goes to Syonagar for posting about his build using the same motherboard and uploading the Clover folder. System Specs: Core i5 4570 Gigabyte H81m-DS2 Klevv SSD Neo N510+ 480gb Primary Samsung SSD 850 EVO 500gb Backup while getting everything working. Toshiba HDW120 2 TB HDD for storage. WD Blue 500gb 7,200rpm storage Sapphire Radeon RX570 8gb Works OOTB 16gb Corsair Vengeance LP 1600mhz DDR3 (2 X 8G DIMMS) Firewire card 2k 34" monitor USB installer creation. I created a USB installer on my aging 08 MBP using creatinstallmedia in terminal using the following command sudo /Applications/Install\ macOS\ High\ Sierra.app/Contents/Resources/createinstallmedia --volume /Volumes/MyVolume Clover installed using default for UEFI. UEFI Drivers: ApfsDriverLoader.efi AudioDxe.efi FSInject.efi OsxAptioFixDrv.efi PartitionDxe.efi SMCHelper.efi VBoxHF.efi Kexts: Lilu.kext RealtekRTL811.kext For my lan SMCProcessor.kext SMCSuperIO.kext VirtualSMC.kext WhateverGreen.kext OS installed to Klevv SSD (file system APFS) without issues during installation and first boot. RX570 recognised out of the box and runs at up to 2k 144hz. After install and initial setup: System backed up to Samsung SSD using Carbon Copy Cloner. This was incase I screwed up the primary install. Post install: Install Clover on SSD EFI partition. Replace the new Clover folder with Syonagar's Clover folder for Catalina. Reboot Reboot without install USB was successful. First issue was no audio through the HDMI. This was solved buy adding AppleALC.kext and removing VoodooHDA.Kext but this meant I had no onboard audio. At the time I wasn't fuss as I use HDMI audio through my monitor. Clover folder update with the following. UEFI Drivers: ApfsDriverLoader.efi AudioDxe.efi DataHubDxe.efi Fat.efi FSInject.efi NTFS.efi OsxAptioFix3Drv.efi SMCHelper.efi VBoxExt2.efi VBoxExt4.efi VBoxHfs.efi VirtualSmc.efi Kexts: Installed into other folder AppleALC.kext This was so I could have audio via HDMI. Because I removed VoodooHDA.kext I had no onboard audio and AppleALC.kext required a fix to enable onboard audio. Lilu.kext RealtekRTL8111.Kext For Lan SMCProcessor.kext SMCSuperIO.kext VirtualSMC.kext Whatevergreen.Kext Reboot HDMI audio working. Working EFI folder backed up to Samsung EFI partition as well as a zip file on the a separate HDD. Onboard audio fix using Clover Configurator. I found the fix at another site but it is also show by Shaon at I have used ID 13. I now have working onboard audio through the front panel as well as rear output. I have to check to see if this has enabled the line in and mic in as well. A complete list of supported codecs can be found at https://github.com/acidanthera/AppleALC/wiki/Supported-codecs Backup EFI folder. Next Issue was the firewire card causing the system to reboot on shutdown. The card did work without issue in a system using an Asus B85M-G board that I had installed HS and Mojave on. This board started acting flakey which is why I purchase the H81m-DS2. I was fortunate enough to find it brand new at a local retailer. After some trial and error, including testing on a 1st gen i7 with Mavericks installs to confirm the card still worked, I cleaned out the EFI partition and reinstalled clover. I installed the firewire card and then updated all drivers and kexts manually using those that I have listed and selected fix shutdown in Clover Configurator under ACPI-Fixes. Reboot to confirm system still works. Connect portable HDD via Firewire. Firewire works Shutdown to confirm system shuts down. Success. Lastly I enabled trim which appears to have made the boot time increase by about 15-20 seconds. I have searched online and it appears to be common. I have also searched to see if trim enabled is needed with APFS and have read mixed opinions. Any thoughts? Installed Security Update 2020-003 10.13.6 as well as iTunes 12.8.2, iTunes Device Support Update and Safari 13.1.1 Backup system and EFI. I have installed Adobe Production Premium CS5.5 because I am capturing old VHS tapes and the player has firewire out. Premiere Pro works but does tend to crash when I quit as does Photoshop. Unfortunately Di Vinci Resolve doesn't support firewire. Currently search for a solution but I may use the i7 Mavericks system if it becomes a problem because it's only a short term unpaid project and I already own the software. Cheers, Chris
  2. Chris261

    Chris261

    Hi everyone, I'm Chris. I live in Melbourne Australia. I built my 1st Hackintosh in 2008 but the motherboard packed it in and I haven't bothered to try building another one untill now. I currently have a system running SL that I built using an i7 870 on an intel DP55WB board with 8 GB ram and a EVGA GT240 graphics card using the multifail. The only issue is HDMI doesn't work properly. I originally wanted a program like Apeture but didn't have a mac at the time. I bought a MBP but persisted with the 1st machine. I now want a machine similar to a macpro in that I can add HDDs if/when I need with ease but can't justify the price of a macpro at the moment although I may consider As for general computing skill. I can do the basics such as install an os and trouble shooting but I have no idea how to program etc. I have no real technical experience or skills to help but if someone in my area needs help getting a part etc I'm more then happy to lend a hand. Chris
×
×
  • Create New...