FoxND001 Posted September 6, 2018 Author Share Posted September 6, 2018 Update - testing has gone pretty well. The system now seems pretty stable for the past week with VT-D turned off with the current set of patches and config tweaks. I'm calling it good at this point! I'll start rolling this into a good tarball and start putting together a nice setup guide. @Jake Lo, thanks a lot for your help and guidance - I would not have gotten the 5414 to work without your help. Final question - should I post the last set of DSDT files for patching (since I did make a change by turning off VT-D), or do you think the current set of patches are good as is? They seem to work fine, but I thought I'd check with you on this. Thanks again - will begin working on the guide for the 5414. Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted September 6, 2018 Moderators Share Posted September 6, 2018 Probably don't need it if it's still working, but if you want to be thorough, go ahead and attach the files and I'll re-patch them. Link to comment Share on other sites More sharing options...
SabithaSuki Posted April 30, 2019 Share Posted April 30, 2019 I appolgise for the necrobump, but is there a link to the most recent tutorial or clover package? Whenever I do mine It hangs on various points like APFS module start appleUSBHostresources0, VM subsystem is on (I disabled VT-D), or Restore Environment Starting. Is this a bad USB drive or an issue with the most recent debug EFI package? Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted April 30, 2019 Moderators Share Posted April 30, 2019 Just update Clover to latest version with the following settings Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\DataHubDxe-64 Drivers64UEFI\FSInject-64 Drivers64UEFI\SMCHelper-64 Drivers64UEFI\ApfsDriverLoader-64 Drivers64UEFI\AptioMemoryFix-64 Drivers64UEFI\PartitionDxe-64 Install Clover Preference Pane Add to Drivers64UEFI\HFSPlus.efi (Not included in Clover installer) and update kexts as well Link to comment Share on other sites More sharing options...
SabithaSuki Posted April 30, 2019 Share Posted April 30, 2019 What about the drivers posted on this forum. I installed the latest clover with settings to the usb, but I dont know what kexts I need to use here or to be updated (be it from this fourm or otherwise). Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted April 30, 2019 Moderators Share Posted April 30, 2019 the kexts folder can be found in the last debug file posted 1 page back Link to comment Share on other sites More sharing options...
SabithaSuki Posted April 30, 2019 Share Posted April 30, 2019 Yup it worked! It turns out I needed to use the plst included with the latest version of clover instead of with the zip packages. Who knew. All thats left is to replace that wifi! Unfortnatlety This doesn't help. Still cant boot. Link to comment Share on other sites More sharing options...
SabithaSuki Posted May 1, 2019 Share Posted May 1, 2019 So after the install, the brightness is still dim and I get stuck mid boot. Any way to fix that? Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted May 1, 2019 Moderators Share Posted May 1, 2019 post your clover files Link to comment Share on other sites More sharing options...
SabithaSuki Posted May 1, 2019 Share Posted May 1, 2019 Here are all the files I used. CLOVER.zip Im 75% sure it has something to do with the APFS, as when I tried to do a fresh re-load of the boot loader, I accidently clicked the APFS loader, and even after removing the EFI and replacing it, it may still have lingers. I would really just like a preloaded pack as it would save me a lot of effort of having to hash together the old and new plsts, themes, kexts, and EFI's. I plan on posting three other permutations soon and their hang spots. Link to comment Share on other sites More sharing options...
Recommended Posts