itzkr0me Posted October 28, 2013 Author Share Posted October 28, 2013 Ha. So I used the wizard to put those flags in, and manually edited the plist file to add the IntelCapriFB bit... Now I'm booting and sitting at a Mac Logo with a spinning wheel (not the colored one) and it's not booting into my system. Before rebooting, everything worked fine. I very much appreciate the help you guys are giving me. Everything seems to be going smoothly, just have a few bumps I need to figure out. Booting with the manual flags worked, so I'm going to try again.. see what happens. Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted October 28, 2013 Moderators Share Posted October 28, 2013 Attach your boot.plist so we could see what's causing the issue. Link to comment Share on other sites More sharing options...
itzkr0me Posted October 29, 2013 Author Share Posted October 29, 2013 Ok, sorry for the delay. I ended up reformatting and doing everything again. After the OSX installation, everything booted up. Which, of course, leads me to my next issue The system booted in normal mode. My next step was to install EDP. I did this. I took the defaults for a 6220 (model database) and ran EDP. myHack finished and I rebooted my machine. Booted back into normal mode and then the system froze. I'm going to boot into my USB installer again and run myfix, but do you all have any ideas? EDIT** Booting into the Installer and running myFix, InstallExtras seems to have resolved that problem. Link to comment Share on other sites More sharing options...
itzkr0me Posted October 29, 2013 Author Share Posted October 29, 2013 I think i'm straight now. A few issues, one being WiFi remain. Not sure what card I have, need to check that. The second issue is my right USB3.0 ports. They are non-functional. They actually cause the OS to freeze if I plug something into them. I've tried searching and using EDP to install the kexts, but nothing seems to work. Any ideas? Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted October 29, 2013 Moderators Share Posted October 29, 2013 From terminal, enter lspci -nn and display result here. Most likely it's an Intel Centrino and it's not supported. Replace it with an Atheros or Broadcom. Hmm, are you sure you have an E6220 not an E6230? I though USB 3.0 only appears on Exx30 models. My E6220 has (2) USB 2.0, (1) HDMI, and (1) eSata port. Anyway, try solution here. 1 Link to comment Share on other sites More sharing options...
itzkr0me Posted October 29, 2013 Author Share Posted October 29, 2013 HOLY CRAP!!! I DO HAVE A 6230. How could I possibly have messed that up!?!?!?! Sorry about that! From Terminal: 00:00.0 Host bridge [0600]: Intel Corporation Ivy Bridge DRAM Controller [8086:0154] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation Ivy Bridge Graphics Controller [8086:0166] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation Panther Point USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation Panther Point MEI Controller #1 [8086:1e3a] (rev 04) 00:19.0 Ethernet controller [0200]: Intel Corporation 82579LM Gigabit Network Connection [8086:1502] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation Panther Point High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.1 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 2 [8086:1e12] (rev c4) 00:1c.2 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 3 [8086:1e14] (rev c4) 00:1c.3 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 4 [8086:1e16] (rev c4) 00:1c.5 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 6 [8086:1e1a] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation Panther Point LPC Controller [8086:1e55] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] [8086:1e03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation Panther Point SMBus Controller [8086:1e22] (rev 04) 02:00.0 Network controller [0280]: Broadcom Corporation BCM43228 802.11a/b/g/n [14e4:4359] 0b:00.0 SD Host controller [0805]: O2 Micro, Inc. Unknown device [1217:8221] (rev 05) I'm rebuilding EDP right now based on the "correct" package Although, it does say i7 in EDP, when I only have an i5.. any issues forseen there? Link to comment Share on other sites More sharing options...
itzkr0me Posted October 29, 2013 Author Share Posted October 29, 2013 Rebuilt, rebooted. Now my keyboard doesn't work... haha. This is fun, no? Works at the bootloader screen, just not once the OS is loaded. Good news is the other USB ports seem to work. Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted October 29, 2013 Moderators Share Posted October 29, 2013 Check E/E and see if ApplePS2Controller is there. If it is, try running myHack/myfix (full). Then reboot.For the E6230 model, you could try using my Extra files here or link on my signature under E6430.Although you have a Broadcom Wireless card, that model is not supported. Personally I have DW1510 which works OTB. Link to comment Share on other sites More sharing options...
itzkr0me Posted October 29, 2013 Author Share Posted October 29, 2013 Fix one thing, break another. I'll replace the wifi adapter with what you suggested. Non-issue there. Now my sound doesn't work. I'm going to try your link with that kext to see if it fixes it. Link to comment Share on other sites More sharing options...
itzkr0me Posted October 29, 2013 Author Share Posted October 29, 2013 No go on the AppleHDA link in your post. I still get nothing. No devices found. EDIT** Sound is back, by rerunning EDP and choosing Voodoo HDA#3. Will a Dell branded DW1540 WiFi card work OTB? Link to comment Share on other sites More sharing options...
Recommended Posts