Jump to content

Yosemite on E5450


e5450

Recommended Posts

Hello,

there is no nvidia card too. There is only the Intel HD 4400 installed.

I loaded deafult settings in BIOS and set SATA to AHCI. I added slide=0 and nv_disable=1 in Clover boot settings, but still the same error. :(

I disabled Bluetooth in BIOS => still the same error.

Is it possible to disable Bluetooth in Clover? I don't need Bluetooth on my hackintosh.

Now, i bought a BroadCom BCM94322HM8L and will change my Intel7265AC to BroadCom BCM94322HM8L.

Link to comment
Share on other sites

  • Moderators

Your graphics is not loading, it's not a bluetooth issue.

Can you boot to the Clover GUI, use the right arrow to navigate to Options

Hit Enter to select it. Go down to Graphics Injector Menu, hit enter again

What does the "Card DeviceID" show?

 

You might have to change the ig-platform-id that fits your graphics.

Link to comment
Share on other sites

Hello,

thanks for your reply.

Please see the picture in the appendix.

I tried to set in Clover Configurator the following settings:

ig-platform-id: "0x0d220003"
Fake-ID IntelGFX: "0x04128086"


ig-platform-id: "0x0a260006"
Fake-ID IntelGFX: "0x04128086"

 

Still the same error :(

What's about the FakePCIID_HD4600_HD4400.kext and FakePCIID.kext? I only have the following kexts in /EFI/Clover/kexts/Other/


ACPIBatteryManager.kext
FakeSMC.kext
IntelMausiEthernet.kext
VoodooPS2Controller.kext

 

Is it possible to inject the IDs in DSDT?

 

Thanks a lot :)

post-80285-0-34482000-1436900885_thumb.jpg

Link to comment
Share on other sites

I deleted the DSDT.aml from /EFI/Clover/ACPI/patched.

 

I edited the config.plist with

 

- inject Intel

- ig-platform-id: "0x0a260006"

- Fake-ID IntelGFX: "0x04128086"

 

In the appendix, there is a zip file with the content of EFI folder.

 

It is still the same error seen in the picture...

 

I rebooted my Dell after this error. Should i wait a few minutes? At the end i can read the scratched words "still waiting for your device"... I have seen, that the cursor goes a line down after about 20 seconds...

EFI_without_patchedDSDT.zip

Link to comment
Share on other sites

  • Moderators

Ok, I must've missed the miss it the first time. Add GenericUSBXHCI.kext to /EFI/Clover/Kexts/Other. I think your system only have USB3.0 ports, so that is needed to boot the Installer. If that's successful, you can place the DSDT back after.

Link to comment
Share on other sites

Hello,

 

yes, my E5450 has only USB3.0 ports. I inserted GenericUSBXHCI.kext to /EFI/Clover/Kexts/Other, but it is still the same Error.

 

Now, i spent a lot of time in reading Hackintosh Basics an Tutorials.

 

I have a mostly running Yosemite on my E5450. I hope you agree with this solution und you will help me to get the following devices work correct:

 

USB3.0 (not working)

HD4400 (1920x1080 is ok, but i can't move position of windows and at the boot process, there are some graphics errors - picures are in the appendix)

 

I used the Yosemite HDD Installer to install Yosemite on my HDD. Then I installed Clover to get Yosemite starting.

 

Here is the content of /EFI/ (I pressed F4 at Clover Screen )- http://www.markus-reisser.de/OSX/EFI.zip

 

I copied the follwing kexts with KextWizzard to /S/L/E at Yosemite.

 

DisableTurboBoostBattery.kext

FakePCIID_HD4600_HD4400.kext

FakePCIID.kext

IOAHCISerialATAPI_Injector.kext

 

When i use the patched DSDT.aml Yosemite will not start...

 

Thanks a lot :)

 

post-4953-0-41250600-1437862149_thumb.jpg

 

post-4953-0-14034300-1437862215_thumb.jpg

 

post-4953-0-77304400-1437862241_thumb.jpg

Link to comment
Share on other sites

×
×
  • Create New...