tonykai

Hello , According to install guide, I have been download install_tools.zip file into Downloads folder ,then type the following code :- chmod a+x /users/tonykai//Downloads/install_tools.sh sudo /users/tonykai/downloads/install_tools.sh but system notice me : line 54 : gen_debug: command not found Pls help me Thank you

Hello , I was complete installed MacOs Catalina on my laptop by use Olarila.catalina.101.15.4 image (https://www.olarila.com/) on this week . Then add some patches via use HackIntool_v3.4.0 to add Coffee Lake Framebuffer patches. Now UHD 630 can work . But there are still exist two problem on my laptop . 1, Trackpad can't work . i don't know that if it is a common problem . 2, can't adjust screen brightness. Please help me and give some suggestions . Thank you Attachment is my config.plist and kexts photo. config.plist.zip

hello, below is detail hardware configure for my laptop dell 5491: Bios: 1.11.1 CPU: Coffee Lake i5-8300H @2.3G Graphics: Coffee Lake UHD630 Memory: 8GB DDR4 2666MHz Mainboard: DELL 0NFNN4 (CM246 Chipsets) SSD: TOSHIBA 256G NVMe (primary) HDD: SATA ST1000LM049 1T (second) Sound: Realtek ALC256 LAN: Intel I219LM7 Wireless/Bluetooth: Qualcomm QCA61X4A 802.11AC Wireless Adapter I try to install from clover in verbs mode . I found out that screen will stuck at apfs_module_start:1689 Thanks for every information you can give to me . Attachment is error photo and EFI file . config.plist.zip

Hello, below is detail hardware configure for my laptop 5491: Bios: 1.11.1 CPU: i5-8300H @2.3G Memory: 8GB DDR4 2666MHz Mainboard: DELL 0NFNN4 (CM246 Chipsets) SSD: TOSHIBA 256G NVMe (primary) HDD: SATA ST1000LM049 1T (second) Sound: Realtek ALC256 LAN: Intel I219LM7 Wireless/Bluetooth: Qualcomm QCA61X4A 802.11AC Wireless Adapter I had been completely install Mojave 10.14.6 on my laptop DELL 5491. Then I find out these problems: UHD Graphics 630 was only showed 7M Sound card (Realtek ALC256) cannot work, I try inject ID 5/11/13 /21/22/28/56 But it cannot still work Touchpad cannot work Qualcomm QCA61X4A 802.11ac Wireless card cannot work Please help me and give some suggestions to solve it. Attachment is my config.plist config.zip

Dear Jake Lo , I will create usb boot disk under MacOS 10.14.14 system into a new USB disk . then continue use config.plist file and all files under ACPI which come from E7450_A20_tonykai.zip . for the kext folder, i will copy this files which come from CLOVER_20190415.zip BR Kai

Dear Jake Lo , According your suggestion, i enter clover system via USB disk , then go into MacOs , then Mount the EFI partition of the Installed drive in local disk , then delete config.plist file and delete all files and including folders which is belong to under \EFI\CLover\ACPI folder . then copy config.plist file and all files under ACPI which come from E7450_A20_tonykai.zip . then reboot MacOS and remove USB disk . Finally , i can't still go into MacOS . Below is error information pic . i attached current the whole EFI folder which is modified according E7450_A20_tonykai.zip . you can download this current whole EFI folder file ( CLOVER_20190415.zip). https://mega.nz/#!6BFgCK5T!hG9oLjmm1s6Kl2It3ssn5wzdRG_VhEq0qiZoRp9mMeI BR Kai

Dear Jake Lo , According your suggestion, i enter clover system via USB disk with my_original EFI boot system , then enter MacOs after press F4 , I attached Origin.zip which is belong to the whole /EFI/Clover/ACPI/Origin folder. I have one question need your help . When you give patch the files to me , How are i use it ? if i need do below these actions , isn't it ？ 1， remove all files which is belong to under EFI folder . 2, copy the whole EFI folder which come from USB Disk into Local disk . 3，use Exx50_Mojave.zip to replace EFI files base on current files under EFI folder 4, copy patch files which come from you into /EFI/CLOVER/ACPI/patched folder Thanks Kai origin.zip

Dear Jake Lo , According your suggestion, i enter winpe system in my laptop E7450 , then use Universal BIOS Backup ToolKit 2.0.exe tools to backup the BIOS (DellInc.-A20.rom) , then use UEFITool.exe to find the module labeled SetupPrep and extract the PE32 image section . I am search with this GUID then extracting the PE32 body under it would be faster /easier than finding the module per guide 899407d7-99fe-43d8-9a21-79ec328cac21 then use Universal IFR Extractor.exe to extract setup.bin to a readable text file (Section_PE32_image_Setup_SetupPrep_body IFR.txt) then i use Use notepad to search for "DVMT" in the text file, 2 were found at 0x15b and 0x15c then i format a new USB drive to fat32 and create a folder name EFI and extract ( EFI Shell) the Boot folder to EFI folder ,for example: i.e.. /EFI/Boot/bootx64.efi. then i reboot laptop via this new USB Boot system and i can successfully enter command windows . then i enter below these commands, hit enter after each command. setup_var 0x15b 0x3 setup_var 0x15c 0x3 finally ,i exit command windows and reboot laptop and remove USB disk , but i can't still enter MacOS via efi boot system which in local disk (use Exx50_Mojave.zip to replace EFI files base on my original EFI boot file ) , system will still show error information " busy timeout IGPU " . BR Kai Section_PE32_image_Setup_SetupPrep_body IFR.zip

Dear Jake Lo , I will explain my mean. Frist Whether use local disk or USB disk ,i can all enter MacOS via my original EFI boot file , but Graphics HD5500 is showed 7MB. below download link address is original EFI boot file . -- original_CLOVER.ZIP https://mega.nz/#!CQczWQCL!du7F4CiK-vy-O-mtt09uoj1FQuWgXLH8IDtJ4ZqN-iY then i use Exx50_Mojave.zip to replace EFI files base on my original EFI boot file in local disk . finally i find out i can't enter MacOS , system always show error information " busy timeout IGPU ", then i enter Clover option menu ,then select Graphics Injector interface -> select InjectIntel and change value to 0x12345678 for FakeID , i still can't enter MacOS . below download link address is the last EFI boot file ( use Exx50_Mojave.zip to replace EFI files base on my original EFI boot file ) -- CLOVER.ZIP https://mega.nz/#!SNEEAQBD!Mqp5niflQIUTAZ-wSX_3scgZv7cTBZKFPNc0jUMhhrQ So current i only enter MacOS via use USB disk and use my original EFI boot file . BR Kai

Dear Dear Jake Lo , usb flash disk boot is use my original EFI boot file which haven't use Exx50_Mojave files to replace .but Graphics HD5500 is showed 7MB. Beacuse i all can't enter Mac OS via EFI boot files ( use use Exx50_Mojave folder files to replace my original EFI files ) which is in local disk or enter Clover option menu ,then select Graphics Injector interface -> select InjectIntel and change value to 0x12345678 for FakeID . BR Kai

Dear Jake Lo , According your suggestion, I enter MacOS via usb flash disk boot . then copy these two kexts (lilu.kext and Whatevergreen.kext ) into /EFI/Clover/kexts/Other folder.then run two commands " sudo touch /System/Library/Extensions && sudo kextcache -u /" and "sudo touch /Library/Extensions && sudo kextcache -u /" under terminal windows for refresh cache . finally , i reboot my loptop and remove usb flash disk , but System will still show error information to me for busy timeout(0) 60s :IGPU . below is error information picture . by the way , I attached the last clover.zip file which is after replace original files under current EFI folder via use Exx50_Mojave folder give you for reference. You can download clover.zip via click the below link. https://mega.nz/#!SNEEAQBD!Mqp5niflQIUTAZ-wSX_3scgZv7cTBZKFPNc0jUMhhrQ If you would like remote my this laptop to survey this trouble via termviewer ? Current i can't enter MacOS via use Exx50_Mojave.zip boot file , but i can enter MacOS via usb flash disk. Appreciate your reply . BR Kai

Dear Jake Lo , According your suggestion , At frist i set my laptop BIOS to Load Defaults and apply it , then set the BIOS to UEFI/AHCI/Legacy Option ROMs enable and Secure boot Disabled , create a new Boot Options for MacOS. then i completed update MacOs Mojave from 10.14.1 to 10.14.4 after use my original EFI files enter MacOS. then update Clover boot system from v4862 to v4910 .(Note : if i select PartitionDxe-64 option in process of install clover_v2.4k_r4910.pkg , Clover install will be fail .) then i reboot MacOS , I completed to redownload Exx50_Mojave.zip file and unzip it . then i use these files which is under Exx50_Mojave folder to replace original files under current EFI folder and copy this three files (BrcmFirmwareRepo.kext ,BrcmPatchRam2.kext,DisableTurboBoostBattery.kext ) to \library\extensions\ . then use Kext Utility to refresh cache . Finally ,i reboot MacOS , System will still show error information to me for busy timeout(0) 60s :IGPU . Then i reboot laptop ,then enter Clover option menu ,then select Graphics Injector interface -> select InjectIntel and change value to 0x12345678 for FakeID , then click return to the main menu ,then boot macOS , finally , system is still show error information . I attached some pictures and clover.zip which is after replace original files under current EFI folder via use Exx50_Mojave folder give you for reference. You can download clover.zip via click the below link. https://mega.nz/#!DMUh1CbY!ATgbn7zdOSn-YcPs2ZqXSVfBTi-0licifkZLxdlUWE8 BR Kai

Dear Jake Lo , Legacy option Roms is enable for my bios configuration, and Secure Boot is Disabled. So i hope you can give me a whole ‘EFI’ folder files for E7450. BR Kai

Dear Jake Lo, I had been complete modify dvmt value according your post .( setup_var 0x15b 0x3 and setup_var 0x15c 0x3) then i re-install macOS Mojave 14.3, then paste files from Exx50_Mojave.zip into CLOVER folder . finally , the same problem is still exist for show busy timeout 'IGPU' in boot process. i try press O to get to Options under Clover gui,then enable Graphics Injector and Select platform-id and change it to 0x12345678, the same problem is still exist. So please help me give a whole ‘EFI’ folder files . BR Kai

Dear Jake Lo , According your suggestion , I select FakeID and change value to 0x12345678 under clover interface for Graphics option ,then click return to the main menu ,then boot macOS , finally , system code is always stayed for 'IOConsoleUsers:gIOScreenLockState 3 bs 0,now 0, sm 0x0 ' . I waited 10 minutes , system can't still go to MacOS login interface. select platform-id and change value to 0x12345678, The issue is same . By the way , for epair permissions and rebuild cache , if i can use Kext Utility app to do it ? Attached files are error info pic and current my laptop configration info under Bios . BR Kai