saphire Posted May 21, 2012 Share Posted May 21, 2012 Is there anyone use myHack3.1 to boot more than 1 OS and really get graphic to choose different OS ? When it is 10.7.3 and myHack2.1, I write chameleon wizard with GUI and Graphics mode, it can let me choose OS in graphics, but now it is CGI mode with 4 lines for me to choose OS, lion, win, linux, freebsd. I also try to myfix to go, same CGI mode. Link to comment Share on other sites More sharing options...
saphire Posted May 21, 2012 Share Posted May 21, 2012 I found a way to fix my above shown CGI mode to GUI mode sudo cp -R /Volumes/myHack\ OS\ X\ Install\ Disk/Extra/Themes /Extra Have fun! Link to comment Share on other sites More sharing options...
Administrators Bronxteck Posted May 21, 2012 Administrators Share Posted May 21, 2012 correct you add a theme folder to your Extra directory and enable themes in your Boot.Plist Link to comment Share on other sites More sharing options...
Jball5 Posted May 22, 2012 Share Posted May 22, 2012 I have a Dell D830 Nvidia 140M Quadro T9500 Intel Core 2 Duo 2.6GHz. I have a backup of my 10.7.3 install but when I try to upgrade following the procedures in the previous posts I get stuck at [PCI Configuration Begin]. I notice that at that moment during boot the numlock light on the keyboard goes dark and the boot up process freezes. I have replaced the AppleACPIPlatform.kext and adjusted the permissions and ran MyFix still no success. Even tried all the listed Chameleon commands at boot. Any suggestions? Link to comment Share on other sites More sharing options...
Administrators Syonagar Posted May 23, 2012 Administrators Share Posted May 23, 2012 Dear Jball5, Try to re-install Extra from the backup using myhack and then run myfix full mode before rebooting with mach_kernel arch=i386 -v -f Let me know how it went. Cheers! Link to comment Share on other sites More sharing options...
ssprod Posted May 23, 2012 Share Posted May 23, 2012 Greetings fine folks... I can positively report that the AppleACPIPlatform.kext replacement worked perfectly on my D620-intel system.... Many thanks! 1 Link to comment Share on other sites More sharing options...
Jball5 Posted May 23, 2012 Share Posted May 23, 2012 Dear Syonagar, I tried your suggestion and I still get stuck at [PCI Configuration Begin]. I am using the latest MyHack version. Not sure if that has anything to do with it. Thanks. Dear Jball5, Try to re-install Extra from the backup using myhack and then run myfix full mode before rebooting with mach_kernel arch=i386 -v -f Let me know how it went. Cheers! Link to comment Share on other sites More sharing options...
Administrators Bronxteck Posted May 24, 2012 Administrators Share Posted May 24, 2012 and you added AppleACPIPlatform.kext in extra and re ran myfix? try adding npci=0x2000 Link to comment Share on other sites More sharing options...
PeterC Posted May 24, 2012 Share Posted May 24, 2012 G'day folks, 10.7.4 went pretty good for me, No crashes with long load times, but the ACPI fix above solved that. BUT After running myfix full, and a reboot my wireless stopped working. No device detected. The wireless did work from the very first boot of 10.7.4 and for 2 reboots until I ran myfix. In previous versions of lion, a permission repair fixed this sort of problem but no luck so far. I've tried replacing the IO80211 kext with the broadcom 43XX rev 2 kext. My wireless reports as a broadcom 4311. Any suggestions? Link to comment Share on other sites More sharing options...
Administrators Syonagar Posted May 25, 2012 Administrators Share Posted May 25, 2012 Dear PeterC, Try the new EDP3 just released from the forum. It took care of the EDP and myhack compatibility issue. Cheers! Link to comment Share on other sites More sharing options...
Recommended Posts