catmater 11 Report post Posted February 10, 2019 On 2/10/2019 at 8:22 PM, Bronxteck said: catmater what SSD are you using in your setup? SK hynix SC311 SATA 256GB (70000P10) m2 revision - 450/460 mb/s read/write perfomance. I'm drop out SATA-100-series-unsupported.kext , i think is useless for my hardware, but maybe it wrong? Share this post Link to post Share on other sites
Nancy10 0 Report post Posted February 10, 2019 I decrypted and removed bit locker, but I still have the error of disk IO failed, I am going to go back to try with my old clover configuration. EDIT: Nope, nothing works anymore. Share this post Link to post Share on other sites
catmater 11 Report post Posted February 10, 2019 1 hour ago, Nancy10 said: I decrypted and removed bit locker, but I still have the error of disk IO failed, I am going to go back to try with my old clover configuration. EDIT: Nope, nothing works anymore. Try to this config - added some missed driver for mojave to clover. catmat-7480-mojave.v2.zip Share this post Link to post Share on other sites
Nancy10 0 Report post Posted February 10, 2019 2 hours ago, catmater said: Try to this config - added some missed driver for mojave to clover. catmat-7480-mojave.v2.zip I am still trying to install HS not Mojave EDIT : it didn't work. Share this post Link to post Share on other sites
mastermind278 0 Report post Posted February 10, 2019 16 hours ago, Jake Lo said: @Nancy10 Try my Mojave guide here Use this bootpack, files goes into /EFI/Clover replacing the default installed by Clover Kexts in ../kext/Other/CopyToLE should be copied to /Library/Extensions after installation as part of post install. Good luck 7480_HD620.zip Thank you so much, have been fighting audio issues for days and your bootlick works!!! Share this post Link to post Share on other sites
Jake Lo 1540 Report post Posted February 11, 2019 @Nancy10 Make sure you set BIOS as this Set to Default, apply, then set SATA Operations to AHCI, set Boot List Option to UEFI, Disable Secure boot Share this post Link to post Share on other sites
Nancy10 0 Report post Posted February 11, 2019 20 hours ago, Jake Lo said: @Nancy10 Make sure you set BIOS as this Set to Default, apply, then set SATA Operations to AHCI, set Boot List Option to UEFI, Disable Secure boot I did that and it didn't work. how can i fix this ? like it says disk2s1 error, and i only have 2 disks the internal and the us drive: is it the internal it is having a problem with ? or the usbdrive ? EDIT : Could the windows OEM REcovery Partition be the problem ? Share this post Link to post Share on other sites
Nancy10 0 Report post Posted February 12, 2019 Any one ? I truly can't boot to the installer. Share this post Link to post Share on other sites
Jake Lo 1540 Report post Posted February 12, 2019 Disable the drive and see if you could boot up the USB installer. I had the issue on PM981 and needs to be replace with a supported drive, but unsure of PM961. Share this post Link to post Share on other sites
Nancy10 0 Report post Posted February 12, 2019 58 minutes ago, Jake Lo said: Disable the drive and see if you could boot up the USB installer. I had the issue on PM981 and needs to be replace with a supported drive, but unsure of PM961. I disabled the drive and the problem persisted, I assume it's my USB installer. Very weird because I already did boot the installer before on the same laptop like hours before this error came up. I'll create a new Installer. Share this post Link to post Share on other sites
