esmith1966 Posted August 17, 2019 Share Posted August 17, 2019 Now i am getting a "USB accessory needs Power" error message whenever I plug in a USB drive... Link to comment Share on other sites More sharing options...
Administrators Hervé Posted August 17, 2019 Administrators Share Posted August 17, 2019 Try and re-generate a USBPorts kext with Hackintool app. Link to comment Share on other sites More sharing options...
esmith1966 Posted August 18, 2019 Author Share Posted August 18, 2019 Generated a kext, but didn’t seem to work. Also there were boot hanging issues Link to comment Share on other sites More sharing options...
Administrators Hervé Posted August 18, 2019 Administrators Share Posted August 18, 2019 Hmm... I think I remember experiencing this before... from memory under Mojave... The USBPorts injector may not have been generated under the correct running conditions. Get rid of it (rebuild your cache if you installed it in /L/E or /S/L/E) and replace it byRehabman's USBInjectAll and reboot. Then try and re-generate USBPorts again. Your Clover setup and/or kexts arrangement could be incorrect too. You know the drill by now... Link to comment Share on other sites More sharing options...
esmith1966 Posted October 5, 2019 Author Share Posted October 5, 2019 I cannot figure out how to get hackintool to work properly. Is there a simple tutorial about this? Cannot determine what patches to check off in the Bootloader menu. Will the E6530 have 15 usb ports as it only has 4 on the outside and an unknown amount internally. Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted October 5, 2019 Moderators Share Posted October 5, 2019 Here's the easier way I could think of without all those boot arg the Hackintool.app suggested Install USBInjectall.kext, add the port limit patches to Config file under kextToPatch. Reboot Now run the Hackintool.app, test all the USB ports with USB2/USB3 devices. If you have a dock and plan to use it, make sure it's docked prior. Remove any ports not being use. Export the kexts or SSDT*.aml files from the app. Now you have 2 options: Add the USBPort.kext to /E/C/k/Other Remove USBInjectAll.kext and the port limit patches from Config or Keep USBInjectAll.kext, remove the port limit patches Add the exported SSDT*.aml to /E/C/A/Patched Here are the port limit patches to add Source #1 com.apple.iokit.IOUSBHostFamily Find: 83FB0F0F Replace: 83FB3F0F #2 com.apple.driver.usb.AppleUSBXHCI Find: 83F90F0F Replace: 83F93F0F If the patches doesn't work on Beta5, best to use follow the steps while running 10.14.6 Port limit patches for 10.14.6 is here Link to comment Share on other sites More sharing options...
esmith1966 Posted October 6, 2019 Author Share Posted October 6, 2019 I followed your directions. Got the USB drives working with USBport.kext and no port limit patches I have all four standard USB ports working, BUT the internal webcam is not appearing at all Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted October 6, 2019 Moderators Share Posted October 6, 2019 With the port limit patches, all USB ports should be enabled. If your Webcam does not show automatically as an internal device when you launch the Hackintool, then there's something wrong. Check if it's enabled in the BIOS or perhaps the port limit patches are not complete or not working properly. Example: Link to comment Share on other sites More sharing options...
esmith1966 Posted October 6, 2019 Author Share Posted October 6, 2019 These are without hackintool USBports.kext Link to comment Share on other sites More sharing options...
esmith1966 Posted October 6, 2019 Author Share Posted October 6, 2019 This is with USBports.kext without patches... No webcam Link to comment Share on other sites More sharing options...
Recommended Posts