nickelnoff Posted August 22, 2019 Author Share Posted August 22, 2019 Thanks @Jake Lo - That's the one I've got implemented and have the dGPU disabled. I have this set in BIOS: Enabled Switchable Graphics (Check) Discrete Graphics Controller Direct Output Mode - disabled (uncheck) Anywhere to go in this config to output through mDP, HDMI or TB3? Side question: Is the Dell Wireless 1830 (DW1830) a straight easy swap for the 7510 ? No extra antenna or anything is have to deal with ? I saw a few threads with folk having problems getting the full AC speed - how did it work for you ?? Link to comment Share on other sites More sharing options...
Administrators Hervé Posted August 22, 2019 Administrators Share Posted August 22, 2019 DW1830 is a 3 x antenna cards when most M.2 cards are 2 x antennas only. If you only connect 2 x antennas to the DW1830, it'll not run at full speed. Link to comment Share on other sites More sharing options...
nickelnoff Posted August 22, 2019 Author Share Posted August 22, 2019 I assume the stock Intel is 2 x antennas as well in that case. What's the easiest AC M.2 card in that case ? Your article below suggests perhaps the DW1560 but be great to get something that will just work with no hacking Link to comment Share on other sites More sharing options...
Administrators Hervé Posted August 22, 2019 Administrators Share Posted August 22, 2019 Choice is extremely limited as far as M.2 cards are concerned: DW1560 (BCM4352) -> patch required DW1830 (BCM4360) -> works OOB DW1820A (BCM4350) and related -> patch required but probably best avoided given the amount of headache & trouble it's given to users; no guarantee it'll work... I know of no other M.2 cards that are fully supported. There are Atheros cards of course but Mojave dropped support for those even though Atheros cards that worked up to High Sierra can be re-used under 10.14 once the Atheros40 kext from previous macOS release is re-installed. This being said, M.2 cards based on AR946x/AR9565/AR9485 chips are not supported to the full and only operate at limited rate. They require a re-written Atheros40 kext. 1 Link to comment Share on other sites More sharing options...
nickelnoff Posted August 22, 2019 Author Share Posted August 22, 2019 @Hervé Thanks for confirming looks like I'll shoot for a 1560 in that case. Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted August 22, 2019 Moderators Share Posted August 22, 2019 With these settings, you should be able to connect to HDMI and mDP external monitors. Enabled Switchable Graphics (Check) Discrete Graphics Controller Direct Output Mode - disabled (uncheck) TB3 is not fully supported yet I think, so it's not hot pluggable. You'll need it connected before booting to access it. Go with the DW1560, minimum patching require. Just need 4 kexts and you're good to go. 1 Link to comment Share on other sites More sharing options...
nickelnoff Posted August 23, 2019 Author Share Posted August 23, 2019 I guess there is still work to be done on getting the P530 working properly. Ordered the DW1560! Link to comment Share on other sites More sharing options...
nickelnoff Posted August 23, 2019 Author Share Posted August 23, 2019 Sort of moved forward a bit removed the InjectIntel from the config and now using some Device Properties and KextToPatch properties. @Jake Lo Sort of good news > when plugging in an HDMI cable the machine reboots (using BIOS options as discussed above). config.plist.zip Link to comment Share on other sites More sharing options...
nickelnoff Posted August 23, 2019 Author Share Posted August 23, 2019 Slowly moving in the right direction. mDP output is now working - no audio HDMI still nothing TB3 nothing config.plist 3.zip Link to comment Share on other sites More sharing options...
nickelnoff Posted August 23, 2019 Author Share Posted August 23, 2019 @Jake Lo Do you know if LSPCON was needed for the Dell Precision 7510? Updated Clover and WEG Kexts and Lilu to latest. Need to run further analysis but now getting TB3 graphics and HDMI output. However not at the same time. mDP was working but has now stopped working. Any one know what the AppleALC layout-id should be set ? Link to comment Share on other sites More sharing options...
Recommended Posts