Jump to content

68x

Recommended Posts

Hi guys,

 

I'm new to OSXLatitude and I was very happy to see UX32VD support. So kudos for your work! ;-)

Unfortunately I already upgraded my RAM to 10GB, so the guide is not working properly for me. Darwin stops at "Failed to load kext com.yourcompany.driver.AppleACPIPS2Nub"...

This is probably due to the limitations of Cameleon. How can I get myhack to work with Clover? Or am I dealing with a different problem?

 

Regards,

NebulaH

 

If you explain the process you did so far from the beginning so we can help you since our EDP doesn't support clover but we can guide for clover issues.

Link to comment
Share on other sites

Hi EMlyDinEsH,

 

Fortunately I was able to get Everything up and running using clover, although I'm not sure if I have too many (or conflicting) stuff on my machine.

The InsanelyMac forum has quite some info on the zenbook prime aswel. What I really like about OSXL, is the maintenance of packs and guides, something alike would be nice for Clover like solutions.

It's quite complicated to get the right config.plist, SSDT.aml, kexts and DSDT.aml files... but it seems things are running quite nice now.

 

Regards,

NebulaH

Link to comment
Share on other sites

Hey guys,

 

Seems like you have accomplished a lot. I read this thread a few others and there is too much scattered information about getting OSX working on the UX32VD.

 

Can someone tell me what is the current best/easiest way to get it setup with OSX?

 

I have the UX32VD-DH71 model with 6GB RAM: http://www.amazon.ca/ASUS-UX32VD-DH71-CA-13-3-Inch-Ultrabook-802-11agn/dp/B009PO9NU0/ref=sr_1_2?ie=UTF8&qid=1368028595&sr=8-2&keywords=zenbook

 

 

And one more question, will I be able to output to 2x1080p monitors simultaneously using the HDMI and VGA ports?

 

Thanks!

Link to comment
Share on other sites

Hi EMlyDinEsH,

 

Fortunately I was able to get Everything up and running using clover, although I'm not sure if I have too many (or conflicting) stuff on my machine.

The InsanelyMac forum has quite some info on the zenbook prime aswel. What I really like about OSXL, is the maintenance of packs and guides, something alike would be nice for Clover like solutions.

It's quite complicated to get the right config.plist, SSDT.aml, kexts and DSDT.aml files... but it seems things are running quite nice now.

 

Regards,

NebulaH

Hi, can you please mention how you got clover working?

 

Did you first install OSX following the method in this thread and than later replaced your chameleon bootloader with clover? What was the procedure? Thanks! 

Link to comment
Share on other sites

Hi Gihad,

 

Well actually I installed Mac OS 10.8.2 through unifail and installed Clover according to Phelics12's method posted on the insanelymac-forum in the "zenbook prime fixes mods tweaks..." thread (post 295). Then I replaced de config.plist, DSDT.aml, SSDT.aml and kexts from 68x (who posted the guide on this forum). I will redo everything until I get things done in the proper order without breaking stuff. 

I'm planning to write a how-to for UX32VD users who'd like to have a dual boot 10.8.2(+) and Debian Linux system with a shared home/users partition.

 

Regards,

NebulaH

Link to comment
Share on other sites

Hi,

 

I have made a install USB with MyHack and os x 10.8.3

installation with -x flag is succesful but when i start os x 10.8.3 with -x or -x -v PCIRootUID=0 and/or GraphicsEnabler=No and/or npci=0x3000 it hangs at [PCI Configuration end, bridges 4 devices 13].

 

can someone help me, i want to run os x 10.8.3

 

i use the UX32VD zenbook.

Link to comment
Share on other sites

The reason why I am recommending to use my Extra.zip is because it will get you passed the PCI begin/end error.

 

The newer builds of chameleon support the Zenbook, so you should be able to use more than 4GB of RAM.

Link to comment
Share on other sites

×
×
  • Create New...