Gemini44

Almost same device we are using except cpu and ram size, I asked this question because my IOReg was sligtly different yours. I 'll try fresh install mojave tomorrow and i'll use your clover#8, I hope I can succeed this time. Many thanks.

I'll buy DW1560 or DW1830 and try it. Thank you very much @Hervé.

Fresh installed mojave but i did not find any solution. I tried direct add-on kexts /L/E folder cached and repaired permissions but no luck. Is it relevant with "PciRoot (0x0)/Pci(0x1C,0x02)/Pci(0x0,0x0) for PCI0@0->RP03@1C,2->PXSX@0." adress. Does it vary by device? I guess i'll buy dw1560 or 1830. Thank you very much.

Hello all, Sorry my English, I have HP elitebook 840 G3 with i7-6500, 24 gb 2133 mhz ram 500 gb 850 evo M.2 ssd drive, dw1820a wifi-bt, latest BIOS. I installed Catalina without problem (first disabled wifi in bios). I used @Hervé trick for enable the wifi. I didnt install any extra kexts and i m booting with usb flash. Wifi seems works, but after 5-10 minutes later system is freezing. If i disable wifi, system looks working normally. Am i making a mistake somewhere? (root/Pci path?) My brother have Latitude 7490 and it has same problem (unsolwed). By the way 2 of wifi card have same MAC in laptop and label (i think they are not fake) PS: I wanted to use debug file but always failed ( /usr/bin/gen_debug write protected and sip disabled). so i attached my ioreg and clover config.plist. Thank you very much for your help. ioreg_config_plist.zip

Thanks for reply. 1. It was weird but when i'm installing mojave without SATA-100-series-unsupported.kext at the end of the installation i recieved installation failure. Now i removed it. 2. Looks like same MAC adress. I added photo. I'm booting device and sometimes KP, sometimes doesn't see wifi, sometimes boot normally, everytime different problem, and now says "WI-FI: No Hardware Installed" and i'm shutting down but it is not and i manually shut down device. I disabled wifi, now it is not enabling and freezing laptop. Thank you very much for your efforts @Hervé.

I followed your guide and i inject properties. Laptop booting normally but if wireless on, system freezing after that. Just mouse working and i have to power off manually. If wireless off no problem. I added debug report file. Thank you very much @Hervé debug_21683.zip

Hello all, I have Latitude 7490 with i5-8350, 32 gb Kingston 2666mhz ram (i upgraded 8gb ddr4 2400mhz), 128 gb hynix M.2 ssd drive, dw1820a, 1.11.0 BIOS. Before i used dw1560 wifi-bt (i broke) and i have to replaced it to dw1820a. I used @Hervé's Clover pack #8 (thanks a lot) i succeed installation but when i enabled wireless in bios, laptop is not booting. PS: I enabled BT in bios and it seems working. I posted my debug report file and boot picture. Thanks in advance. debug_12457.zip

I am very sorry. Problem solved (I was looking at arbitrary section instead of properties). HDMI output works fine. Thank you very much for your helps Jake Lo.

I downloaded Hervé's Revised Clover pack #8 he has mentioned about hdmi fix, i replaced my config.plist to Hervé's, but i haven't got any changes. Thanks.

I created new USBPort.kext via hackintool and fixed the icons view. Thank you very much Jake Lo.

I removed USBInjectAll.kext & USB port limit patches but it isn't worked and then i removed USBPort.kext too and reboot voila my usb hdd shows up. I have a new problem my external drives shows as internal, is it normal? Thanks in advance Jake Lo.

I added BrcmFirmwareRepo.kext & BrcmPatchRAM2.kext to efi/Clover/kexts/Other folder and seems BT works. Right USB port is not working, am i broke something about config or kexts? Finally, should i install in efi kexts to L/E? Thanks Jake Lo.

I fixed touchpad issue via VoodooI2C.kext and VoodooI2CHID.kexts, thank you Jake Lo. I enabled DellBIOSPatch. But i have no Bluetooth device and touchpad buttons not working. Right USB port has been working before when i installed VoodooI2C and VoodooI2CHIDkexts. Now not working. I attached debug file. Do i need patch ACPI files for stable system? Thank you all. debug_20955.zip

Hello, Sorry my poor English, I have Latitude 7490 with i5-8350, 32 gb Kingston 2666mhz ram (i upgraded 8gm ddr4 2400mhz), 500 gb samsung 970 evo plus nvme M.2 ssd, dw1560, 1.11.0 BIOS specs. I used Hervé's topic Clover pack #7 (thanks a lot) but i did not success and always KP. So i tried different EFI packs (shared 7490 topics) and i started installation but i recived errors from installer at the and of the final stage but 7490 booted normally. Bluetooth (i did not see sys. pref.), trackpad and trackpad buttons is not working. System indicates my ram as 2400mhz. I guess i have to edit my config files (different ram config and wifi). I know how is edit DSDT and SSDT files but i don't know which patches i should make. I did not find any guide for Latitude 7490, or can i use rehabman's guide? I want to more stable laptop). I posted my debug report file. Thanks in advance. debug_31725.zip