Jump to content

FUJITSU S6410 IG invalid firmware error


robi62
 Share

Recommended Posts

Hi I bought a fujitsu s6410 as a replacement for my dell d430 mainly because of ram limitations.

 

I installed Lion gm which is working fine but I cannot control brightness because of error

IG: Invalid firmware max backlight setting

 

I saw in project osx that there was a solution with adding Device (PNFL) to dsdt

 

I downloaded DSDTE from evo86

 

When I add the device PNLF to dsdt and try to compile it keep getting errors.

 

I am not very good at editing dsdt ....

 

Can someone point me in the right direction????? :(

Link to comment
Share on other sites

  • Replies 24
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

this is the linux one

 

 

To run a command as administrator (user "root"), use "sudo <command>".

See "man sudo_root" for details.

 

________________________________________

( Lay on, MacDuff, and curs'd be him who )

( first cries, "Hold, enough!". )

( )

( -- Shakespeare )

----------------------------------------

o

o

___

{~._.~}

( Y )

()~*~()

(_)-(_)

[email protected] ~ $ lpcsi

bash: lpcsi: command not found

[email protected] ~ $ lspci

00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03)

00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03)

00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03)

00:1a.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 03)

00:1a.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 03)

00:1a.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 03)

00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03)

00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 03)

00:1c.2 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 3 (rev 03)

00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 03)

00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 03)

00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 03)

00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03)

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f3)

00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 03)

00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03)

00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 03)

00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 03)

04:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8055 PCI-E Gigabit Ethernet Controller (rev 14)

0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11a/b/g (rev 01)

1c:03.0 CardBus bridge: O2 Micro, Inc. OZ711SP1 Memory CardBus Controller (rev 01)

1c:03.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 02)

1c:03.3 Mass storage controller: O2 Micro, Inc. Integrated MS/xD Controller (rev 01)

[email protected] ~ $

 

I think they are the same

 

Link to comment
Share on other sites

Hi when I first boot in lion I had no dsdt my res was not right then I installed switch res to get right one

1280x 800

Then with pcwiz dsdtgui I created my dsdt

 

I tried now the one from linux after compiling it with evo86 dsdte but still problem persists

 

 

 

Link to comment
Share on other sites

 Share


×
×
  • Create New...