Administrators Bronxteck Posted May 11, 2016 Administrators Share Posted May 11, 2016 maybe try a different Ethernet kext and see if it persists. or check energy saver pref pane to see if it has lan sleep enabled. Link to comment Share on other sites More sharing options...
radionoise Posted May 11, 2016 Author Share Posted May 11, 2016 Laptop sleeps okay when on battery even with ethernet cable plugged in. The problem occurs only when on AC power. All corresponding options in power saving are unchecked. Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted May 11, 2016 Moderators Share Posted May 11, 2016 Replace with this DSDT - rename it first DSDT - sleep.aml.zip Link to comment Share on other sites More sharing options...
radionoise Posted May 12, 2016 Author Share Posted May 12, 2016 Thanks! It works. Any chances of disabling discrete graphics through DSDT? Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted May 12, 2016 Moderators Share Posted May 12, 2016 Can you send me the debug.log in /EFI/Clover/Misc Link to comment Share on other sites More sharing options...
radionoise Posted May 12, 2016 Author Share Posted May 12, 2016 Can I enable debug in Clover on my USB drive? I have three partitions now (EFI FAT32, Windows NTFS, El capitanHFS+). OSX is on the third partition. When I try to install Clover it doesn't install to EFI partition. Link to comment Share on other sites More sharing options...
Administrators Bronxteck Posted May 12, 2016 Administrators Share Posted May 12, 2016 do you point the installer to install to your Apple Volume? Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted May 12, 2016 Moderators Share Posted May 12, 2016 run in terminal diskutil list /dev/disk0 (internal, physical): #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *256.1 GB disk0 1: EFI EFI 209.7 MB disk0s1 2: Apple_CoreStorage Macintosh SSD 63.5 GB disk0s2 3: Apple_Boot Recovery HD 650.0 MB disk0s3 /dev/disk1 (internal, virtual): #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Macintosh SSD +63.1 GB disk1 Logical Volume on disk0s2 75DADC16-4B7F-4C7D-9660-10A1C2A9FC02 Unencrypted If you encounter virtual disk, see the red above, then run the following diskutil cs revert /dev/disk1 Reboot and install Clover again. Should go to EFI partition now. Link to comment Share on other sites More sharing options...
radionoise Posted May 13, 2016 Author Share Posted May 13, 2016 Here is my debug.log. I installed latest clover but screen is still flashing during boot when on battery. Can you help fixing it please? I think it depends on DSDT patches. Screen started flashing after trying your first DSDT patches when brightness controll became available. debug.log.zip Link to comment Share on other sites More sharing options...
radionoise Posted May 15, 2016 Author Share Posted May 15, 2016 I fixed screen flickering. Just replaced IntelBacklight.kext with a new one. Also I added EmuVariableUefi-64.efi driver to preserve brightness, volume level after reboots One thing that bothers me then happened. After several restarts I had kernel panic at assertion in AppleIntelFramebuffer.kext. That was due to DVMT value magically reverted back to 0x1 and I had to set it to 0x3 again. After that I cannot see Nvidia chip in System report now, so I think it's disabled now. I looked for my wireless card and discovered that it's not 1/2 miniPCIe but NGFF. I suppose Dell DW1560 (Broadcom BCM94352Z) is the only card that would work in my case? I updated my first post. Link to comment Share on other sites More sharing options...
Recommended Posts