WalterWolf Posted September 7, 2017 Author Share Posted September 7, 2017 I finally completed following the guide, thanx for writing ! Worked fine since i fixed permissions, worked on config.pls and created own dsst-file. Now I can´t even boot or re-install. Any suggestions ? Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted September 7, 2017 Moderators Share Posted September 7, 2017 Reboot with USB installer and select the installed drive. what update did you do to the Config file? Link to comment Share on other sites More sharing options...
WalterWolf Posted September 7, 2017 Author Share Posted September 7, 2017 8. Repair permission and rebuild cache. Run command from terminal sudo chmod -Rf 755 /L*/E* sudo chown -Rf 0:0 /L*/E* sudo touch -f /L*/E* sudo chmod -Rf 755 /S*/L*/E* sudo chown -Rf 0:0 /S*/L*/E* sudo touch -f /S*/L*/E* sudo kextcache -Boot -U / 9. Go to System Preferences Enable Clicking for Trackpad Allow apps downloaded from: Anywhere for Security & Privacy Note: For Sierra, run this in terminal instead: sudo spctl --master-disable 10. Generate own SMBios and SSDT Launch /EFI/Clover/Config.plist with Clover Configurator (Included in Tools attached below) On the left, click on SMBIOS Click on the magic Wand on the right Select the model most suited for your system or use same model included in bootpack, generate a new serial Close Clover Config and save the file. Execute ssdtPRGen.sh from terminal (Included in Tools attached below) Place generated SSDT.aml in /EFI/Clover/ACPI/Patched 11. Make sure to disable hibernation as it's a prerequisite to get sleep & wake to work Ok on a Hackintosh: sudo pmset hibernatemode 0 sudo rm -f /var/vm/sleepimage sudo pmset hibernatefile /dev/null It seems now, the machine can´t read the hdd, loading starts, but nothing happens. Testing the hdd now Link to comment Share on other sites More sharing options...
WalterWolf Posted September 7, 2017 Author Share Posted September 7, 2017 HDD works fine. Any ideas ? Link to comment Share on other sites More sharing options...
Administrators Hervé Posted September 7, 2017 Administrators Share Posted September 7, 2017 Describe: "the machine can´t read the hdd, loading starts, but nothing happens." Right now, it seems the bootloader is not installed or configured properly. Link to comment Share on other sites More sharing options...
WalterWolf Posted September 9, 2017 Author Share Posted September 9, 2017 Thanx, but why can´t I just install again from USB? Also the same problem there. I checked RAM, HDD, Bios + Win still works What shall I do now ? Link to comment Share on other sites More sharing options...
Administrators Bronxteck Posted September 11, 2017 Administrators Share Posted September 11, 2017 make sure you have HFSPlus.efi in your clover drivers folder. if you used APFS as the drive format instead of HFS plus then you need APFS.efi driver in clover drivers. if it's a core storage volume then you need to revert it using terminal. Link to comment Share on other sites More sharing options...
WalterWolf Posted September 15, 2017 Author Share Posted September 15, 2017 thanx bronx! but i (tried to) did the conversion as mentioned before and now i´m stuck booting. HDD-Swap shows no difference Link to comment Share on other sites More sharing options...
Administrators Bronxteck Posted September 15, 2017 Administrators Share Posted September 15, 2017 make sure to transfer the working EFI folder to the hdd then. Link to comment Share on other sites More sharing options...
WalterWolf Posted November 1, 2017 Author Share Posted November 1, 2017 Finally it worked out. Did everything from scratch. Thank's to all of you <3 But sometimes the dell freezes. Only restart helps. I guess thermal issues, because after freeze hardwaretest implemented also freezes. Also Artifacts in the bootscreen, no matter which Bios rev. Audio not working Link to comment Share on other sites More sharing options...
Recommended Posts