Sndesigner Posted January 7, 2016 Share Posted January 7, 2016 Yes, thanks, Jake. I have gotten this far in the installation process of clover and have a question about: 26. Hit Continue, then hit Customize. Select these items: Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\OsxAptioFixDrv-64 (DOES THIS MEAN THAT I ONLY SELECT OsxAptioFixDrv-64 and DESELECT the other options within Drivers64UEFI? Or do I include all the files within Drivers64UEFI?) Link to comment Share on other sites More sharing options...
Moderators Jake Lo Posted January 7, 2016 Moderators Share Posted January 7, 2016 Just OsxAptioFixDrv-64, deselect the rest if it's selected. 1 Link to comment Share on other sites More sharing options...
karelson Posted January 7, 2016 Share Posted January 7, 2016 Hey Jake, I followed your guide. USED 32GB USB, E6230 A10. After the install USB, I boot my computer bios, configure the bios, The reboot with F12. after selection boot USB device I get invalid partition table, hit ENTER and nothing. Any ideas? thanks Link to comment Share on other sites More sharing options...
Administrators Hervé Posted January 7, 2016 Administrators Share Posted January 7, 2016 Sounds like the bootloader did not install properly... Try and reinstall it. Link to comment Share on other sites More sharing options...
Sndesigner Posted January 8, 2016 Share Posted January 8, 2016 OK, I did every step correctly to set up my bootable USB Drive, prepared using the El Capitan Clover Guide. I chose the correct EFI folder too. I set up my bios per the instructions in the document on my Dell Latitude E6230 / 8GB RAM / 256GB HDD / Core i5-3340M 2.70 GH. When I try to boot by pressing F12 and choosing the USB drive in the list, I get screen that says 'Invalid partition table!" Any suggestions? It will not boot into clover. Link to comment Share on other sites More sharing options...
Administrators Bronxteck Posted January 8, 2016 Administrators Share Posted January 8, 2016 not all usb sticks are bootable try with another you know can boot an os. or try doing a low level format of the usb stick first. Link to comment Share on other sites More sharing options...
Sndesigner Posted January 8, 2016 Share Posted January 8, 2016 Where in the guide does it talk about a bootloader? Where do I go about reinstalling a bootloader? Link to comment Share on other sites More sharing options...
Administrators Bronxteck Posted January 8, 2016 Administrators Share Posted January 8, 2016 im not sure about a guide but all hackintoshes need a boot loader to load OS X wether it is chameleon or clover. Link to comment Share on other sites More sharing options...
Sndesigner Posted January 8, 2016 Share Posted January 8, 2016 OK I'm stuck. I I don't know how to get past this invalid partition table screen. I did everything right in making my usb stick. The troubleshooting you mentioned was to do a low level format and remake the installer usb disk? I don't know how to do a low level format on a mac. The USB drive is brand new and it works well. Good brand... HP. I am not sure why I would need to reformat at low level or if that is truly the problem. Can you offer any other suggestions? I really appreciate it! Link to comment Share on other sites More sharing options...
Administrators Bronxteck Posted January 8, 2016 Administrators Share Posted January 8, 2016 well sometimes it helps clear out any issues with previous disk formats. try a security wipe on it in OS X then format it guid install your boot loader and see if it boots to the boot loader before remaking the installer. if guid does not work then format it as mbr partition and reinstall the boot loader. the point is to make sure it boots a boot loader before you waste any more time. Link to comment Share on other sites More sharing options...
Recommended Posts