Jake Lo

Not seeing your Bluetooth in the USB port. what does it have? Replace Config file and add CodecCommander.kext to /Library/Extensions Repair permissions and rebuild cache config.plist.zip

Add this to /EFI/Clover/kexts/Other Replace Config file to /EFI/Clover What bluetooth does it have? Update the above, reboot, then send me the debug files. config.plist.zip

You didn't use the files I linked above, goes into /EFI/Clover. Replace, not merge Also install latest Clover with the following settings: Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\AppleImageCodec-64 Drivers64UEFI\AppleKeyAggregator-64 Drivers64UEFI\AppleUITheme-64 Drivers64UEFI\DataHubDxe-64 Drivers64UEFI\FirmwareVolume-64 Drivers64UEFI\FSInject-64 Drivers64UEFI\SMCHelper-64 Drivers64UEFI\ApfsDriverLoader-64 Drivers64UEFI\AptioMemoryFix-64 Drivers64UEFI\PartitionDxe-64 Install Clover Preference Pane Finally add to Drivers64UEFI\HFSPlus.efi (not included in Clover installer)

Try this, replace contents into /EFI/Clover 5558_mido.zip

Trim for for SSD only, not for mechanical drives.

Make sure to set BIOS accordingly. Load Defaults. Apply. Then set it to UEFI AHCI Legacy Option ROMS enabled Secure boot disabled Boot to Clover GUI, press F4 Now compress and attach the Clover folder I'm assuming this is your USB installer?

Can you boot with the USB installer and then selecting the newly installed drive?

Boot to Clover, press F4 and then F2. Continue to OSX Run and attach debug files.

Try updating the bootpack with this, goes into /EFI/Clover Generate a new serial number with Clover Configurator so you have yourself a unique key than anyone else.

Try this, replace contents into /EFI/Clover E7250_A19_HS.zip

Try this, replace contents into /EFI/Clover Remove the following from /EFI/Clover/drivers64UEFI OsxAptioFixDrv-64.efi Reboot and post your status

The origin folder is a bit of a mess with duplicate filenames. Can you clear the folder, then follow the steps again? Post new Origin folder again. You could try this bootpack for now for A17. Replace files into /EFI/Clover Copy kexts in /EFI/Clover/kexts/Other/CopyToLE to /Library/Extensions Repair permissions and rebuild cache

What BIOS version are you running? Boot to Clover GUI, press F4 and then F2. Continue to OSX. Run and attach the debug files here

@Richard Piola Welcome to OSXLatitude Richard. First off, you're using the wrong files for this system. You should at least go with the closer match E7450. There's a high Sierra bootpack here If you would prefer a bootpack for E7250, boot to Clover GUI, press F4. Now compress and attach /EFI/Clover/ACPI/Origin folder here, I'll patch the files for you. Create a new bootpack for E7250 for you to test. Hopefully will fix most of those issues. The Caplock is known with the current ApplePS2Controller.kext. Tap twice to enable, then twice to disable. Newer PS2 kext like VoodooPS2Controller by Rehabman or ApplePS2SmartTouchPad by EmlyDinesh might have the fix for it but you'll lose the touchpad or other features since they are not build for Alps. You can try Dr. Hurts kext, which is the best kexts for Alps at the moment.

try this config config.plist.zip

You can start by creating an installer following my Clover guide here. Then add the attached contents into /EFI/Clover I see you already have BIOS A14, make sure to set settings to UEFI, AHCI, Secure boot disabled, Legacy Option ROMs enabled, XD CPU Support enabled Once booted to Clover, press F4, then F2. Then continue the installation process. If failed to boot, then post the KP / Error and attached the Clover folder for review and patching. 3446_installer.zip

Try adding this to /Library/Extensions Repair permissions and rebuild cache DisableTurboBoostBattery.kext.zip

Add CodecCommander.kext to /Library/Extensions Repair permissions and rebuild cache

You have different version of BIOS than my files when it was posted. So I had to patch your files and also update some kexts and patches for 10.13.6.

Here, replace contents into /EFI/Clover E7270_mcintosh.zip

Try this Config. If still not work, try booting from other USB ports config.plist.zip

here you go config.plist.zip

I assume you're installing 10.13.6? You'll need a new USB port patch. Add the one on the bottom to your Config file

post your Clover folder

what version of BIOS do you have? You can 1st boot to Clover, press F4 and then F2 Then press the spacebar and select verbose + debug 0x100 mode Post the screenshot of the KP and attach the Clover folder here for review