Jump to content

Bluetooth Firmware Uploader


EMlyDinEsH

Recommended Posts

This kext not working under 10.11 simply because Apple change single value in its bluetooth kext.

 

IOProviderClass has changed from IOUSBDevice (in 10.10-) to IOUSBHostDevice

credit: pokenguyen

 

To solve the problem, we need to change corresponding (your bluetooth ID) key value in BluetoothDevInfoInjector.kext/info.plist to make it compatible with 10.11.

Link to comment
Share on other sites

I'm having some problems with AzureWave AW-CE123H under OS X El Capitan 10.11. I've tried to edit the IOUSBHostDevice but Bluetooth still not working. It works flawlessly in 10.10 with BTFirmwareUploader.kext. Can anyone help me with this ? Thanks a lot

Link to comment
Share on other sites

I'm having some problems with AzureWave AW-CE123H under OS X El Capitan 10.11. I've tried to edit the IOUSBHostDevice but Bluetooth still not working. It works flawlessly in 10.10 with BTFirmwareUploader.kext. Can anyone help me with this ? Thanks a lot

 

 

This kext not working under 10.11 simply because Apple change single value in its bluetooth kext.

 

 

To solve the problem, we need to change corresponding (your bluetooth ID) key value in BluetoothDevInfoInjector.kext/info.plist to make it compatible with 10.11.

 

Will take a look at this change and  update my kexts asp as I'm busy lately so did not find time to check 10.11. Thanks for sharing the information.

Link to comment
Share on other sites

Hi sssyurrr,

I have tried to include bcm4352.kext as well in my system, but still no luck. 

 

A bit history, before yosemite, my laptop running maverick with wifi & bluetooth working flawlessly (BCM94352HMB - Device ID: 04CA 200B). I tapped pin 51 so i can turn ON & OFF bluetooth via sys pref. After upgrade to Yosemite 10.10.3, my bluetooth works around 2 hours, after that disappeared. Until now i'm struggling to bring back the bluetooth but still no luck. Hmmm.. now i'm clueless and begin to think to switch to USB dongle instead :(

 

Cheers,

 

Can you get me your ioreg and system log without my kext? Also try to remove battery and reset bios then try to turn on again. PM me so i can debug.

Link to comment
Share on other sites

Sorry for late reply, i dont see your BT device in ioreg. can you do rest BIOS and remove battery then do a clean boot and get me your system log/ioreg?

 

Hi.. Thanks Bro... i tried your new version and its not working.. i managed to get my bluetooth device details from windows..

Vendor ID 13D3 Product ID 3404 and i've extracted the firmware and enclosed. Please help me fix this..!

BCM20702A1_001.002.014.1443.1479.hex.zip

post-77761-0-47784000-1435679355_thumb.jpg

Link to comment
Share on other sites

@everyone, new version 2.8.5 release so please test and let me know results. Thanks

Good morning, I just upgraded to 10.10.4 and bluetooth shows in the system, however, i cannot connect devices (everything worked in 10.10.3 with 2.8 ver.). With 2.8 release and 10.10.4, I was able to connect Apple Mice and connection stayed OK for few seconds and then lost it. Just upgraded to 2.8.5 the bluetooth device is loaded normally but cannot connect to any bluetooth devices. details are below and please help. Thank you. 

 

Product ID: 0x3404

  Vendor ID: 0x13d3  (AzureWave Technologies, Inc.)

  Version: 1.12

  Serial Number: 54271E6ADDAE

  Speed: Up to 12 Mb/sec

  Manufacturer: Broadcom Corp

  Location ID: 0x1d130000 / 4

  Current Available (mA): 500

  Current Required (mA): 0

  Built-In: Yes

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...