Jake Lo

what do you mean "with Clover". Aren't you using Clover as loader?

Ok, make a few changes to your alternative Config to add graphics acceleration. See if this works. Post screenshot of KP please config.plist.zip

Make sure you have applied the updates accordingly Also fix permission and rebuild cache after every change or update

See here to post debug files

I was using latest Clover Configurator 4.55, I guess that made changes to the Config if you don't have the latest Clover v4289 Slow because you don't have graphics acceleration. Ok, I'm merged the 2 Configs. See if this works. config.plist.zip

I just added the extra patch for Hynix to the last Config + murad3994.zip you said works except no bootable device except windows so it doesn't work either?

can you attach your current Clover folder?

Try this new Config. Added Bit swap block size 0x10) -Syscl for Hynix/ Plextor NVMe config.plist.zip

enable AddPNLF in Config file

got it, hopefully this fixes it. Seems this system uses Bat1 rather than Bat0 Your debug shows you're using VoodooPS2Controller 1.8.24. Use latest 1.8.28 and disable TRIM support in the Config kexttoPatch. Should fix the Trackpad Preference DSDT-fixBattery.zip

What other issue?

Fn+F3 and Fn+Pause for Brightness Control up and down.

@tonio92 Replace the attached contents into /EFI/Clover Files updated for HS GT720M disabled via DSDT E5440_Disable_GT720M.zip

Set BIOS to UEFI, AHCI, Legacy Option ROMs enabled Boot to USB installer, select SSD Once on Desktop. Install Clover Install for UEFI booting only Install Clover in the ESP Drivers64UEFI\OsxAptioFixDrv-64 Install RC scripts on target volume Install Clover Preference Pane Copy the EFI folder from USB to SSD EFI partition Reboot without USB If still failed, go to BIOS, Boot Option. Click Add and create a new boot option for Clover, point to /EFI/Clover/CLOVERx64.efi. Move new boot option to the top.

Conexant CX20751/2 Use AppleALC.kext & Lilu.kext Layout-id = 28

Assuming you had install Clover to the SSD... Under BIOS UEFI Boot Option, click Add Name it Clover or whatever you like, then browse to /EFI/Clover/CLOVERx64.efi. Save it and move it to the top

can you send debug with BIOS.aml instead of DSDT.aml?

Re-upped new files. Just made some changes to DSDT.aml Please upload new debug files after the changes

@tonio92 according to your screenshot, your system has Optimus (Nvidia card + HD 4400). YOu'll need a different set of patch DSDT/SSDT. Can you confirm? What version of BIOS are you running? Can you boot to Clover GUI. Hit F4 in the keyboard. Compress and attach /EFI/Clover/ACPI/Origin folder here for patching.

Check out this article http://hackintosher.com/blog/get-nvme-m-2-ssds-show-high-sierra-hackintosh-install/

Try these new files. Replace Config and DSDT, and add AppleHDA_ALC668 to /L/E Remove AppleALC from /EFI/Clover/kexts/Other Repair permission and rebuild cache Hopefully the new files fix the following: Battery Status DisplayPort Audio output to external monitor Headphone static noise fix XPS12_fixes.zip

See here for AR9565

What error did you get when booting from HD? Does it have the same version of Clover and EFI files? Replace it with this version

Wrong patches for E6230. This system has IDT 92HD93 not ALC292. Although you have it correct in the Config hot patches. No multitouch for Alps kext, only 2 fingers scrolling, tap and drag.

boot with verbose & debug 0x100 mode, take a picture and upload it when it KP