Jake Lo

Your EFI folder is a bit messy. Delete /EFI/Clover/drivers64UEFI and install Clover from here with the following settings Clover for UEFI booting only Install Clover in the ESP UEFI Drivers\Recommended drivers AudioDxe DataHubDxe FSInject ApfsDriverLoader AptioMemoryFix HFSPlus Additonal drivers PartitionDxe Themes (optional) Install Clover Preference Pane (optional) Remove from /EFI/Clover/kexts/Other: BrcmFirmwareRepo <- goes into /L/E not clover kext, you already have BrcmFirmwareData FakePCIID_Intel_HD_Graphics <- not needed with Whatevergree FakePCIID_Intel_HDMI_Audio <- not needed with Whatevergreen FakePCIID_XHCIMux <- for USB 2.0 only LiluFriend <- goes in /L/E if you want Lilu and plugins to run from /L/E. Not needed if Lilu and plugins in clover kexts

If you're going to use the SSDT-xxx, you need to keep USBInjectall.kext or just use USBPorts.kext and delete USBInjectall.kext + SSDT-xxx

try adding to boot arg -igfxnohdmi

Why keyboard type did you set it to? Use ANSI

Go to /EFI/Clover/ACPI/Origin and clear al the files Reboot to Clover GUI, press F4, continue booting Mount EFI partition, compress and attach the Origin folder for review. For static noise in headphone, download latest CodecCommander.kext and move it to /Library/Extensions Repair permissions and rebuild cache

How are you disabling the Nvidia? I don't see a patched SSDT in Origin or Patched folder regarding the Nvidia or how to disable it.

Remove FakePCIID_Intel_HDMI_Audio & IntelGraphicsFixup.kext

Please run IOREG with HDMI connected, save, compress and attach it here

Post debug file with HDMI monitor connected

Replace the Config with this. Remove the USBPort.kext and add USBInjectAll.kext Reboot. Launch Hackintool. Plug in USB 2/USB 3 devices, set internal if internal...etc. Export when done. Copy the exported SSDT-xx.aml to /EFI/Clover/ACPI/Patched Remove the 4 USB Port limit Patches from the attached Config or restore your current Config and reboot. Check all ports are working config.plist.zip

add to boot arg, assuming it's charging, just not updating status bar abm_firstpolldelay=16000

You need to add ACPIBatteryManager.kext

With these settings, you should be able to connect to HDMI and mDP external monitors. Enabled Switchable Graphics (Check) Discrete Graphics Controller Direct Output Mode - disabled (uncheck) TB3 is not fully supported yet I think, so it's not hot pluggable. You'll need it connected before booting to access it. Go with the DW1560, minimum patching require. Just need 4 kexts and you're good to go.

Known issue with the BIOS resetting. See this alternative fix

I believe there's an option in the BIOS to enable / disable switchable graphics. I think you have switchable graphics Enable since you're booting with iGPU but have discrete graphics disabled via patching. That said, I believe the external connections (DP & HDMI) can be enable even though it's connected the to discrete card. There's an option is the BIOS that allow external connections through the iGPU. Make sure you have that enabled. Update: Found the options from my old guide for 7510 with HD530, not P530 Enabled Switchable Graphics (Check) Discrete Graphics Controller Direct Output Mode - disabled (uncheck)

Hmm, seems by setting SMBIOS to MBP13,3 enables the graphics acceleration. Which Config file are you using to boot?

How were you able to capture this screenshot if it KP'd? Which bootpack did you use? I had attached one for Skylake(HD520) and one for Kabylake (HD620), looks like you have the Kabylake model. If you're able to get into the system, just repair permissions and rebuild cache. Reboot. If you're not able to boot into the system, then do this At Clover gui, press O to get to Options. Go down to Graphics Injector and select it Select both FakeID and platform-id and change them to 0x12345678 Continue booting Repair permissions and rebuild cache Reboot normally

DW1560

Add CodecCommander.kext

add new boot arg -igfxvesa -v

post IOReg with DP connected

The DW1830 requires 3 antennae. Did you only connected 2? I used the 3rd from the WWAN slot

Open Config.plist with Clover Configurator Under Devices, go to Properties, look for PciRoot(0x0)/Pci(0x1c,0x02)/Pci(0x0,0x0) and delete it Go to Kernel and Kext patches, and enable DellSMBIOSPatch Save file Add AirportBrcmFixup.kext to /EFI/Clover/kexts/Other for wifi Add BrcmFirmwareRepo.kext & BrcmPatchRAM2.kext to /L/E for Bluetooth Repair permissions and rebuild cache Reboot

remove the wifi patches in the config file, it's patched for DW1820a

You probably need to generate a new USBPorts since mine is for E7470. Lookup Hackintool