Jump to content

Jake Lo

Moderators
 View Profile  See their activity

  • Posts

    14365

  • Joined

  • Last visited

  • Days Won

    868

 Content Type 

Everything posted by Jake Lo

  1. Jake Lo
    @ICEGalaxy Please post what you did to fix the audio and include the files As for SDCard reader, install this For Fn key, try karabinar-Element app
  2. Jake Lo
    Hmm, you must be using an older version of Clover. There's only AptioMemoryFix.efi, no AptioMemoryFix-64.efi in the latest Clover.
  3. Jake Lo
    @Jazzoo Then I guess layout-id 11 is the best you'll get or you could learn how to patch your own Audio. https://osxlatitude.com/forums/topic/1946-complete-applehda-patching-guide/#comments For wake, try adding to boot arg darkwake=0
  4. Jake Lo
    You could try different layout-id for ALC293. See if there's one that will allow external mic
  5. Jake Lo
    Did you read the entire thread? Especially this post, that the Nvidia can't be disable?
  6. Jake Lo
    Try the voodooI2C/HID version found in Hervé 's guide for his Latitude 7490.
  7. Jake Lo
    @DiogoSilva48 try this one https://osxlatitude.com/forums/topic/13583-kext-voodoops2-support-for-elan-touchpad/
  8. Jake Lo
    The obvious problem is that it's running in an external drive. Move the drive internally
  9. Jake Lo
    @Darkshadow7890 If your system is same as this, it might be you can't disable the iGPU and need to use the Nvidia. In that case you can only run High Sierra as there's no support for Nvidia after. The last post include a guide and bootpack.
  10. Jake Lo
    try going into sound preference->Input and select Line In
  11. Jake Lo
    try this one and boot with verbose mode if it gets stuck again to see where it hangs config.plist.zip
  12. Jake Lo
    at clover gui, press O to get to Options. Add to boot arg -igfxvesa Do that until the installation is complete, then you could boot without.
  13. Jake Lo
    Use latest version v5119 and replace your boot files from here, goes into /EFI/Clover replacing the old
  14. Jake Lo
    Please post your OC folder Also post full system specs. Are you able to boot successfully, just no graphics acceleration?
  15. Jake Lo
    try this config.plist.zip
  16. Jake Lo
    That's too bad. Thanks for the help.
  17. Jake Lo
    if you have AppleBacklightInjector.kext in /L/E or /S/L/E, remove it and repair permission, rebuild cache Replace SSDT-PNLF.aml in the patched folder with the attache run in terminal to reset nvram sudo nvram -c SSDT-PNLF.aml.zip
  18. Jake Lo
    @wellingtonsa Optimus does not work on Hacks so your nvidia is disable via SSDT patching. As for you Wifi, it probably has an unsupported device...perhaps Intel? You'll need to replace it with a supported device like DW1560, DW1830 or DW1820A. See list of known supported/unsupported devices here
  19. Jake Lo
    @linuxchan6 I'm running Catalina/Clover and just updated the 5510 to latest BIOS 1.14.2 without any issue. Are you running with static DSDT or hot patching? If with static DSDT, then you'll need to repatch your new DSDT.
  20. Jake Lo
    try different layout-id for audio 13, 15, and 77
  21. Jake Lo
    @gamersab You have both AptioMemoryFix.efi and EmuVariableUefi.efi in your drivers/UEFI folder. Install one or the other, not both. Like Hervé suggested, if you're using EmuVariableUefi.efi, make sure to install RC Scripts when you're installing Clover. AptioMemoryFix.efi does not need it.
  22. Jake Lo
    @AkshayBhat Please give this version a try https://osxlatitude.com/forums/topic/13583-kext-voodoops2-support-for-elan-touchpad/
  23. Jake Lo
    Your NVMe drive most likely don't have PM. Try adding NVMEFix.kext Audio...strange your Config shows layout-id=13 but your IOReg files show layout-id=3, yet generic_ioreg.kext shows layoutid=3 as well. So you must've some conflict somewhere. Your Intel wifi/BT combo is not ready for support yet. Though you should be able to find IntelBlueboothIjector somewhere that might work. There's also Intel wifi semi support as well, you can find that in one of our research section. Currently the system with crash if the Intel kext is loaded on boot, so you'll need to manually load it after boot and you'll need to hardcode in the SSID and password in the info.plist of the kext
  24. Jake Lo
    @yaseen m khan What does a Windows driver have anything to do with MacOS? Doesn't matter, the issue has already been solved.
  25. Jake Lo
    @duypham312 Yes, that's the same behavior I have for my E7470, but only if you just boot up the system. If it had gone through a sleep cycle prior to inserting the external monitor, it'll work fine.
×
×
  • Create New...